Roland XP-80 Manuel du propriétaire télécharger pdf (Page 105)

...........................................................................................................

When you use quantization at recording, set parameters in

the Recording Quantize window. To open the Recording

Quantize window, press [F4] (Quantize).

✳ Recording Quantize setting will be retained until it is

reset next time.

Type (Quantize type)

OFF: Quantization will not be applied to recording.

GRID: Grid quantization will be applied to recording.

SHUFFLE: Shuffle quantization will be applied to recording.

Resolution

Specifies quantization time interval as a note value.

For Grid Quantize available choices are , , , , ,

, and .

For Shuffle Quantize you can choose either or .

Strength (Grid quantize strength)

This parameter is used when Grid Quantize is selected. It

specifies how much the notes will move (correct) toward the

timing intervals specified by the Resolution parameter. If

you want notes to be move all the way to the nearest unit of

the specified Resolution for maximum quantization, set

Strength to 100%. As this value lowers, notes will move (cor-

rect) less from their original timing. With a setting of 0%, the

note locations will not change at all.

Rate (Shuffle quantize rate)

This parameter is used when Shuffle Quantize is selected. It

specifies how far a down-beat specified by the Resolution

parameter will be separated from the following up-beat.

With a setting of 50%, the timing of the up-beat note will be

at the exact mid point between the down-beat and the fol-

lowing down-beat. With a setting of 0%, the up-beat note

will move to the same timing as the previous down-beat.

With a setting of 100%, it will move to the same timing as

the following down-beat.

Count In

Specifies the way in which recording will begin.

0: Recording will begin immediately when you press

[STOP/PLAY].

1: When you press [STOP/PLAY], a 1-measure count (play-

back) will be included just before recording start position,

and recording will commence when the start position is

reached.

2: When you press [STOP/PLAY], a 2-measure count (play-

back) will be included before recording start position, and

recording will commence when the start position is reached.

Wait Note: Recording will begin when you play a note or

press the Hold pedal.

TRK (Recording track)

Selects the recording destination Phrase track or Pattern. The

cursor will move to the selected recording destination

Phrase track.

Phrase tracks containing performance data will be marked

with “o” on the display and Phrase tracks without perfor-

mance data with “-.” Phrase tracks that contain performance

data but are not to play back will be displayed in grey.

When recording Patterns, nothing will be displayed here.

PART

Selects the Part to use for recording.

When recording a Part with the number corresponding to

the Phrase track’s, selecting a Phrase track will also select the

correspondingly numbered Part. There is no need to select a

Part here.

Use this parameter when you want to record using a Part

with a number different from the Phrase track’s or recording

your performance in a Pattern.

✳ If you’ve selected Patch mode or Rhythm Set mode,

“Patch Mode” or “Rhythm Set Mode” will be dis-

played instead of “PART.”

✳ If a Layer Performance has been selected, Parts indicat-

ed with “o” (Local Switch parameter set ON) will be

recorded as you press the key.

Patch/Rhythm Set

The name of the Patch or Rhythm Set assigned to the current

Part will be displayed in parentheses (). To change the Patch

or Rhythm Set, modify the group and number. This process

also applies for recording in Patch mode or Rhythm Set

mode.

107

Chapter 4. Playing back and recording a song

1 2 ... 100 101 102 103 104 105 106 107 108 109 110 ... 243 244

Roland XP-80 Manuel du propriétaire Page 105

Commentaires sur ces manuels

Roland XP-80 Manuel du propriétaire Page 105

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Roland XP-80