Roland XP-80 Manuel du propriétaire télécharger pdf (Page 62)

EFX Ctrl 1 (EFX Controller 1)

Select the controller to control EFX Ctrl 1 parameter with

Control Source. Set the amount of EFX parameter change

using Depth.

EFX Ctrl 2 (EFX Controller 2)

Select the controller to control EFX Ctrl 2 parameter with

Control Source. Set the amount of EFX parameter change

using Depth.

EFX Ctrl Peak&Hold (EFX Controller Peak&Hold)

Use Peak&Hold to specify how EFX parameter values will

be held after receiving pedal messages.

OFF

: EFX parameter values will not be held even if pedal

messages are received.

HOLD

: EFX parameter values will be held when pedal mes-

sages are received.

PEAK

: EFX parameter values will be held when pedal mes-

sages are received. But if a parameter value greater than the

current one is received while Hold is still ON, the new value

will be held.

✳

When using this function, make sure you also set the

Hold-1 parameter (PATCH/LFO&Ctl/Control Switch)

ON.

✳

If HOLD is selected for Peak&Hold, you must also set

the Hold parameter (SYSTEM/Control/Control

Source) to the type of pedal message to be controlled.

✳

If PEAK is selected for Peak&Hold, you must also set

the Peak parameter (SYSTEM/Control/Control

Source) to the type of pedal message to be controlled.

Chorus display

On this display you can make the Chorus settings for how

chorus will sound and be output.

Level (Chorus level)

Adjusts the volume level of the chorus sound.

✳

This setting will also affect Chorus Level parameter

(PATCH/Effects/General) value.

Rate (Chorus rate)

Adjusts modulation speed for the chorus.

Depth (Chorus depth)

Adjusts modulation depth for the chorus.

Pre-Delay

Adjusts time from when the direct sound begins to when the

chorus sound is heard. Higher values create a more spacious

sound.

Feedback (Chorus feedback level)

Adjusts the amount of chorus sound that is returned (fed

back) to the chorus. Higher values create a more intense

effect.

Output (Chorus output assign)

Specifies how chorus sound is to be output.

MIX

: The sound will be output from the MIX OUTPUT jacks

just as it is.

REVERB

: Reverb will be applied.

MIX+REV

: The sound will be output from the MIX OUTPUT

jacks and to reverb.

✳

This setting can also be made on the General display

(PATCH/Effects).

Reverb display

This display is used for making reverb effect settings such as

reverb type and reverb time.

Type (Reverb/Delay type)

Selects reverb or delay type.

ROOM1

: Short, dense reverb

ROOM2

: Short, sparse reverb

STAGE1

: Reverb with greater late reverberation

STAGE2

: Reverb with strong early reflections

HALL1

: Reverb with clear reverberation

HALL2

: Reverb with rich reverberation

DELAY

: Conventional delay

PAN-DLY

: Delay with echoes that pan left and right

Level (Reverb/Delay level)

Adjusts the level of the reverb (or delay) sound.

✳

This setting also affects Reverb Level parameter

(PATCH/Effects/General) values.

Time (Reverb/Delay time)

For any ROOM1–HALL2 Type, this parameter adjusts

reverb time. For DELAY or PAN-DLY, this parameter

adjusts delay time. Higher values make for a more spacious

sound.

Chapter 3. Creating your own sounds

[PATCH]

➞

[F6] (Effects)

➞

[F4] (Chorus)/[F5] (Reverb)

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 243 244

Commentaires sur ces manuels

Pas de commentaire

Roland XP-80 Manuel du propriétaire Page 62

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Roland XP-80