220
● Control Change
status 2nd byte 3rd byte
BnH kkH vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
kk=control number : 00H - 78H (0 - 120)
vv=value : 00H - 7FH (0 - 127)
* This message is not received if the Ctrl Change parameter (Rec Select win-
dow) is OFF.
● Program Change
status 2nd byte
CnH ppH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
pp=Program number : 00H - 7FH (prog.1 - prog.128)
* This message is not received if the Prog Change parameter (Rec Select
window) is OFF.
● Channel Aftertouch
status 2nd byte
DnH vvH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=Channel Aftertouch : 00H - 7FH (0 - 127)
* This message is not received if the Channel Aft parameter (Rec Select win-
dow) is OFF.
● Pitch Bend Change
status 2nd byte 3rd byte
EnH llH mmH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
mm,ll=Pitch Bend value : 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* This message is not received when the Pitch Bend parameter (Rec Select
window) is OFF.
■ Channel Mode messages
● All Sound Off (Controller number 120)
status 2nd byte 3rd byte
BnH 78H 00H
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
● Reset All Controllers (Controller number 121)
status 2nd byte 3rd byte
BnH 79H 00H
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
● Omni Off (Controller number 124)
status 2nd byte 3rd byte
BnH 7CH 00H
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
* The same processing will be done as when an All Note Off message is
received.
● Omni On (Controller number 125)
status 2nd byte 3rd byte
BnH 7DH 00H
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
* The same processing will be done as when an All Note Off message is
received.
● Mono (Controller number 126)
status 2nd byte 3rd byte
BnH 7EH mmH
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
mm=mono number : 00H - 10H (0 - 16)
* The same processing will be done as when an All Note Off message is
received.
● Poly (Controller number 127)
status 2nd byte 3rd byte
BnH 7FH 00H
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
* The same processing will be done as when an All Note Off message is
received.
■ System Exclusive messages
status data byte status
F0H iiH, ddH, ......, eeH F7H
F0H : System Exclusive message status
ii = ID number : This is the ID number (manufacturer ID) that
specifies the manufacturer whose exclusive mes-
sage this is. Roland’s manufacturer ID is 41H.ID
numbers 7EH and 7FH are defined in an expan-
sion of the MIDI standard as Universal Non-real-
time messages (7EH) and Universal Realtime
Messages (7FH).
dd,..., ee = data : 00H - 7FH (0 - 127)
F7H : EOX (End Of Exclusive)
* These messages are not received if the Sys.Excl parameter (Rec Select
window) is OFF.
3.2 Messages not recorded during recording
■ Channel Mode messages
● Local On/Off (Controller number 122)
status 2nd byte 3rd byte
BnH 7AH 00H
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
vv=value : 00H,7FH (Local off, Local on)
● All Note Off (Controller number 123)
status 2nd byte 3rd byte
BnH 7BH 00H
n=MIDI channel number : 0H - FH (ch.1 - ch.16)
* When an All Note Off message is received, all notes of the corresponding
channel that are on will be sent Note Off’s, and the resulting Note Off mes-
sages will be recorded.
3.3 Messages acknowledged for synchronization
■ System Common messages
● Song Position Pointer
status 2nd byte 3rd byte
F2H mmH llH
mm,ll=value: 00 00H - 7F 7FH (0 - 16383)
● Song Select
status 2nd byte
F3H ssH
ss=value : 0 - 7FH (0 - 127)
* This message can be received when the sequencer is stopped. It will not
be received while in the Edit display or Microscope display.
■ System Realtime messages
● Timing Clock
status
F8H
* This message will be received if the Sync Mode parameter (SEQUENCER/
Setup/SEQ System Setup) is SLAVE.
● Start
status
FAH
* This message will be received if the Sync Mode parameter (SEQUENCER/
Setup/SEQ System Setup) is SLAVE or REMOTE.
● Continue
status
FBH
* This message will be received if the Sync Mode parameter (SEQUENCER/
Setup/SEQ System Setup) is SLAVE or REMOTE.
● Stop
status
FCH
* This message will be received if the Sync Mode parameter (SEQUENCER/
Setup/SEQ System Setup) is SLAVE or REMOTE.
Chapter 12. Supplementary material
Commentaires sur ces manuels