Roland XP-80 Manuel du propriétaire télécharger pdf (Page 123)

REPLACE: All the data in the copy destination will be over-

written by the copy source data. Only the performance data

of the MIDI channels specified by the Channel parameter

will be overwritten, and data of other MIDI channels will

remain.

Times (Copy times)

Specifies the number of times that the data will be copied to

the copy destination.

Status

Selects the type of data to be copied.

ALL: All types of performance data

NOTE: Note

P.AFT: Polyphonic Aftertouch

C.C: Controller numbers

PROG: Program numbers

C.AFT: Channel Aftertouch

BEND: Pitch Bend

EXC: System Exclusive messages

TUNE: Tune Request

PTN: Pattern Call messages

✳ If the Source track parameter is set to TRK T, the Status

parameter will not be available.

Range

If you have selected NOTE, P.AFT, C.C or PROG for the

Status parameter, use this parameter to set the area.

To copy all Note or Polyphonic Aftertouch data, specify “C-

1–G9.” To copy C4 Note/Polyphonic Aftertouch data, speci-

fy “C4–C4.” To copy Note/Polyphonic Aftertouch data from

C3 to C4, specify “C3–C4.”

To copy all Controller numbers or Program numbers, speci-

fy “0–127.” To copy number 4, set “4–4.” To copy numbers

from 3 to 14, specify “3–14.”

Channel (MIDI channel)

Selects the MIDI channel of the data to be copied.

When you want to copy all the performance data, set this

parameter to ALL. To copy only the performance data of a

specific MIDI channel, select the MIDI channel.

✳ If you set the Source track parameter to TRK T, or if the

Status parameter is set to EXC, TUNE or PTN, the

Channel parameter will not be available.

❶ Make sure that the Track Edit Menu display

(SEQ/TrkEdit) is up.

❷ Press [F6] (Menu) to select Menu 1, then press [F3]

(Copy) to call up the Copy display (SEQ/TrkEdit).

This display can also be called up by moving the cur-

sor to “3 Copy” and pressing [ENTER] on the Track

Edit Menu display (SEQ/TrkEdit). Or press the

numeric key [3] and press [ENTER].

❸ Move the cursor to Source track and select the track(s)

or Pattern from which you want to copy data.

❹ When setting the copy source area by measures, move

the cursor to “Measure” and specify the measure num-

ber at which copying will begin, then move the cursor

to “for” to specify the measure length to be copied.

When using Locate positions, press [LOCATE], and move

the cursor to “From” to select the Locate number at which

you want copying to begin. Then move the cursor to “to”

and select the Locate number at which you want copying to

end.

❺ Move the cursor to the Destination track and select the

copy destination track(s) or Pattern.

❻ Press [d] to move the cursor to “Measure” and specify

the copy destination.

Set the copy destination area using the same procedure as

specifying the copy source area.

❼ Move the cursor to “Mode” and select the copying

method.

❽ Move the cursor to “Times” and specify the number of

times you want the data copied.

❾ Move the cursor to “Status” to select the data to be

copied.

If you have selected NOTE, P.AFT, C.C or P.C for Status,

move the cursor to “Range” and specify the area. The key

areas for NOTE or P.AFT can be specified by pressing keys

on the XP-80’s keyboard.

❿ Move the cursor to “Channel” and select the MIDI

channel from which you want to copy data.

Press [F6] (Execute) to begin copy.

125

Chapter 5. Editing a song

[SEQUENCER]➞[F3] (TrkEdit)➞[3]➞[ENTER]

1 2 ... 118 119 120 121 122 123 124 125 126 127 128 ... 243 244

Commentaires sur ces manuels

Pas de commentaire

Roland XP-80 Manuel du propriétaire Page 123

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Roland XP-80