Roland XP-80 Manuel du propriétaire télécharger pdf (Page 120)

122

Truncate

Deletes unnecessary blank measures at the beginning of a

Phrase track or Pattern.

(Basic Procedure)

❶ Make sure that the Play display (SEQ(Song)) is up.

❷ Move the cursor to song number and select the song to

edit.

❸ Press [F3] (TrkEdit) to call up the Track Edit Menu dis-

play (SEQ/TrkEdit).

✳ If you have selected a song saved on disk in step 2, a

window asks “This Song is not Internal Song. Load

anyway?” If you want to erase the song from the inter-

nal memory and load the new song, press [F5] (OK). If

you decide not to erase the song from the internal

memory, press [F6] (Cancel).

❹ Press [F6] (Menu) to select the menu containing the

desired function.

Each time [F6] (Menu) is pressed, the selection will cycle

through Menu 1, Menu 2, and Menu 3, then back to Menu 1,

and so on.

❺ Press an appropriate button from [F1]–[F5] to select the

desired function.

The selected function’s display appears.

✳ You can also select the desired function by pressing

[INC]/[DEC] or cursor buttons, or turning the VALUE

dial to move the cursor, and pressing [ENTER].You

can also select the desired function by inputting the

number assigned to the function with its respective

numeric key and pressing [ENTER].

❻ In the upper <Target> section of the display, select the

track(s) to be edited.

You can select TRK 1–TRK 16 by pressing TRACK/

PART [1]–[16].

TRK T can be selected by pressing [TEMPO/BEAT].

You can select PTN 001–PTN 100 by pressing [PATTERN]

and specifying a Pattern number.

To specify the editing area, refer to “Setting the editing

area”.

✳ Since two tracks or Patterns only are needed for the

Copy, Merge and Extract functions, you’ll specify

<Source> and <Dest.> (Destination), instead. The pro-

cedure is the same for setting Target.

✳ Once you set Target, the setting is retained for other

track editing.

❼ Set the parameters of various functions in the lower

section of the display.

❽ Press [F6] (Execute) to execute the operation.

After the operation is completed, the display indicates

“COMPLETE.”

✳ To interrupt operation, press [EXIT].

✳ If you don’t like the change you’ve made, you can

undo the most recent track edit. Press [UNDO/REDO]

to restore it to its pre-modified state.

❾ To return to the Track Edit Menu display (SEQ/

TrkEdit), press [EXIT].To return to the Play display

(SEQ(Song)), press [EXIT] again.

Setting the editing area

✳ There are two ways of setting the editing area – using

measures or Locate positions. Both methods cannot be

used simultaneously.

Using measure numbers

You can set the editing area by specifying the starting mea-

sure n and the number of measures m to be edited from the

start measure. For example, setting “Measure 5, for 6” means

track editing will take place from the beginning of measure 5

and continue to the end of measure 10.

❶ Move the cursor to “Measure” and specify the measure

where you want to begin track editing.

❷ Move the cursor to “for” and specify number of mea-

sures that you wish to edit.

Select ALL when you want to perform track editing all the

way to the end of a song.

Using Locate positions

The editing area can also be specified using Locate positions

(from LOC1 to LOC2). For example, if you specify “From

LOC1, to LOC2,” the editing area would extend from LOC1

position just prior to LOC2 position, but not including it.

❶ Press [LOCATE] to light the indicator.

❷ Move the cursor to “From” and select the Locate num-

ber from where you want to begin editing.

❸ Move the cursor to “to” and select the Locate number

where you want editing to end.

❹ To return to assigning the editing area by measures,

press [LOCATE] to turn off the indicator.

Measure number

Chapter 5. Editing a song

[SEQUENCER]➞[F3] (TrkEdit)

1 2 ... 115 116 117 118 119 120 121 122 123 124 125 ... 243 244

Roland XP-80 Manuel du propriétaire Page 120

Commentaires sur ces manuels

Roland XP-80 Manuel du propriétaire Page 120

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Roland XP-80