Roland MC-4 Manuel du propriétaire télécharger pdf (Page 29)

Playing a pattern

Pattern Mode

RPS Settings

Hold down [RPS] and press [F6 (RPS Setting)].

Alternatively, hold down [SHIFT] and press [F4 (RPS)].

The RPS setting screen will appear.

Use [CURSOR (up/down)] to select a parameter.

Use [VALUE] or [INC/DEC] to edit the parameter.

When using RPS during pattern playback, patterns and phrases may

not play back in precise alignment, depending on the timing at

which you press the velocity pads. On the MC-909 you can specify

the playback timing of the phrase, so it will play back in precise

synchronization with the pattern. (RPS Trigger Quantize ->p. 128)

•

REAL:

The phrase will play back immediately, at the timing at which

you pressed velocity pads.

•

16TH, 8TH, QUARTER:

The pattern will be divided into selected note units, and when

you press the velocity pads, the phrase will begin playing at the

beginning of the next note unit.

•

MEASURE:

The pattern will be divided into one-measure units, and when

you press the velocity pads, the phrase will begin playing at the

beginning of the next measure.

* Except when this parameter is set to “REAL,” pressing on the velocity

pads slightly before the actual desired timing will help you

synchronize the phrase to the pattern.

* If the pattern is stopped, the phrase will play back immediately,

regardless of the setting that is selected in the above procedure.

Adjusting the settings of the RPS parts

RPS playback uses dedicated RPS parts that are separate from

conventional pattern playback. The patterns that are assigned to

velocity pads [1]–[16] will play RPS parts 1–16.

Here's how to adjust the settings of these RPS parts.

Hold down [RPS] and press [F6 (RPS Setting)].

Alternatively, hold down [SHIFT] and press [F4 (RPS)].

The RPS setting screen will appear.

Press [F3 (RPS Mixer)].

The RPS Mixer screen will appear.

Use the part mixer section to adjust the volume, pan,

etc. of RPS parts 1–16.

Use [F1]--[F4] to select a parameter, and use the sliders to adjust

the values.

* You can also use [CURSOR] to select a part and parameter, and then

use [VALUE] or [DEC/INC] to adjust the value.

Press [F6 (Close)] to close the RPS Mixer screen.

Parameter

Range Explanation

RPS Set

01–50 RPS set to edit

RPS Part Part 1–16 RPS part to edit

RPS Part Patch

Bank

— Patch assigned to RPS part

RPS Part Patch

Number

—

RPS Part Output

Select

DRY, MFX1,

MFX2,

COMP,

DIR1, DIR2,

RHY

How the original sound of

each part will be output

DRY:

Output to MIX OUT-

PUT jacks without passing

through effects

MFX1 (2):

Output through

multi-effects 1 (or 2)

COMP:

Output through

the compressor

DIR1 (2):

Output to the DI-

RECT 1 (or DIRECT 2)

jacks without passing

through effects

RHY:

Output according to

the settings of the rhythm

set assigned to the part

Remote Key-

board Switch

OFF, ON Refer to p. 128.

[PART ASSIGN] Selects the RPS parts that will be controlled

by the sliders.

If this indicator is not lighted, parts 1–8

will be controlled. If lit, parts 9–16 will be

controlled.

Sliders Adjust the volume, pan, key, and reverb lev-

el of parts 1–8 or parts 9–16.

Function button

Parameter adjusted by the sliders

[F1 (Level)]

Volume of the RPS part

[F2 (Pan)] Left/right position of the RPS part

[F3 (Key Shift)] Transposition of the RPS part

The pitch will change in semitone steps

over a range of +/-4 octaves.

[F4 (Reverb Level)] Reverb level of the RPS part

MC-909_Ref_e.book 29 ページ２００５年６月２８日　火曜日　午後２時５３分

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 179 180

Commentaires sur ces manuels

Pas de commentaire

Roland MC-4 Manuel du propriétaire Page 29

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel d'enregistrement Roland MC-4