Roland MC-4 Manuel du propriétaire Page 142
- Page / 180
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
142
Installing the Wave Expansion Board
An optional Wave Expansion Board (SRX series) can be installed in
the MC-909.
Waveform data, patches and rhythm sets are stored on the Wave
Expansion Board, so you can increase the number of available
sounds by installing the board in the MC-909.
Cautions When Installing a
Wave Expansion Board
901
• To avoid the risk of damage to internal components that can be
caused by static electricity, please carefully observe the following
whenever you handle the board.
1
• Before you touch the board, always first grasp a metal object
(such as a water pipe), so you are sure that any static
electricity you might have been carrying has been discharged.
2
• When handling the board, grasp it only by its edges. Avoid
touching any of the electronic components or connectors.
5
• Save the bag in which the board was originally shipped, and
put the board back into it whenever you need to store or
transport it.
• Use a Philips screwdriver that is suitable for the size of the screw
(a number 2 screwdriver). If an unsuitable screwdriver is used,
the head of the screw may be stripped.
• To remove a screw, rotate the screwdriver counter-clockwise. To
tighten the screws, rotate the screwdriver clockwise.
fig.Screw.e
• Be careful that the screws you remove do not drop into the
interior of the MC-909.
• Be careful not to cut your hand on the edge of the cover or the
opening edge while removing the cover.
911
• Do not touch any of the printed circuit pathways or connection
terminals.
912
• Never use excessive force when installing a circuit board. If it
doesn’t fit properly on the first attempt, remove the board and try
again.
913
• When circuit board installation is complete, double-check your
work.
914
• Always turn the unit off and unplug the power cord before
attempting installation of the circuit board (SRX series; Quick
Start p. 2).
915
• Install only the specified circuit board (SRX series). Remove only
the specified screws (p. 142).
928
• When turning the unit upside-down, get a bunch of newspapers
or magazines, and place them under the four corners or at both
ends to prevent damage to the buttons and controls. Also, you
should try to orient the unit so no buttons or controls get
damaged.
929
• When turning the unit upside-down, handle with care to avoid
dropping it, or allowing it to fall or tip over.
• Do not leave the bottom cover removed. After installation of the
Wave Expansion Board is complete, be sure to replace the cover.
How to Install a Wave
Expansion Board
Install the Wave Expansion Board after removing the bottom panel
cover.
1.
Before installing the Wave Expansion Board, turn off the power
of the MC-909 and all connected devices, and disconnect all
cables, including the Power cable, from the MC-909.
2.
Turn the MC-909 over, remove the screws indicated in the
following diagram, and remove the cover.
fig.Exp-01.e_90
3.
Plug the connector of the Wave Expansion Board into the
connector on the unit, and at the same time insert the board
holder through the hole of the Wave Expansion Board.
fig.Exp-02.e
4.
Use the Installation Tool supplied with the Wave Expansion
Board to turn the holder in the LOCK direction, so the board
will be fastened in place.
fig.Exp-03
5.
Use the screws that you removed in step
2
to fasten the cover
back in place.
tightenloosen
Screws to be removed
Board holder
Connector
Position it as shown
before you install
the board.
LOCK
MC-909_Ref_e.book 142 ページ ２００５年６月２８日 火曜日 午後２時５３分
- Owner’s Manual 1
- USING THE UNIT SAFELY 3
- IMPORTANT NOTES 5
- Before Using Memory Cards 6
- Copyright 6
- Contents 10
- Features of the MC-909 13
- Panel Descriptions 14
- Rear Panel 15
- Getting Ready 16
- An Overview of the MC-909 17
- (Factory Reset) 20
- Pattern Mode 21
- Playing a pattern 24
- Changing the BPM (Tempo) 25
- Muting (silencing) a part 26
- Velocity pads 27
- <RPS Trigger Quantize> 29
- Arpeggiator 30
- Creating an arpeggio style 31
- Chord Memory 32
- Realtime Modify section 33
- Part Mixer 33
- D Beam Controller 35
- Recording a pattern 37
- Recording procedure 38
- Rehearsal 38
- Realtime Erase 39
- Recording Cancel 39
- About the timing scale 40
- Step recording 41
- Tempo/mute recording 42
- Pattern editing 43
- Extract a Rhythm Instrument 44
- Pattern Copy 44
- Data Thin 46
- Edit Quantize 46
- Microscope 48
- Saving a pattern 50
- Patch/Sample 51
- Patch/Sample Mode 53
- Patch Edit 54
- Selecting a patch/rhythm set 55
- Patch editing procedure 56
- T1 T2 T3 T4 59
- Filter Env (Filter Envelope) 61
- Amp Env (Amp Envelope) 63
- LFO1/LFO2 64
- Solo/Porta (Portamento) 65
- TMT (Tone Mix Table) 66
- Rhythm Edit 70
- L.Fade value 76
- U.Fade value 76
- Saving a Patch/Rhythm Set 77
- Copying a Rhythm Tone (Key) 78
- Song Mode 79
- Playing songs 82
- Recording a song 83
- Song editing 84
- Saving a song 85
- Effect on/off 88
- Effect settings 88
- Compressor 89
- Multi-effects 90
- Realtime control of effects 91
- Multi-Effects List 92
- Total Wow/ 102
- 2Voice Pitch Shifter 103
- (MFX2 only) 104
- Right/Center 105
- Center Level 105
- Feedback 106
- Mastering effect 108
- Sampling 109
- Sampling procedure 112
- Dividing a sample during 113
- Sample Edit 114
- Sample Parameters 116
- Truncate 117
- Create Patch 117
- (Auto Chop) 118
- Create Rhythm 119
- Emphasis 120
- Edit Time Stretch 121
- Normalize 121
- Saving a sample 123
- Menu (in Sample Edit) 124
- Panel/Controller 127
- Sequencer/MIDI 127
- System Information 130
- Import SMF 131
- File Utility 134
- USB communication 135
- Undo/Redo 136
- About V-LINK 138
- V-LINK settings 139
- Appendices 141
- Board holder 142
- Connector 142
- Checking that a wave 143
- Connecteur 144
- Support à carte 144
- Vérifier que la carte 145
- Expanding the Memory 146
- Checking that memory is 147
- Ajouter de la mémoire 148
- Vérifier que la mémoire est 149
- Waveform List 150
- Preset Patch List 151
- Preset Rhythm Set List 154
- Preset Pattern List 158
- RPS Pattern List 160
- RPS Set List 162
- Pattern Set List 164
- Song List 165
- Arpeggio Style List 166
- Chord Form List 167
- SRX-05 Special Patch List 168
- MIDI Implementation Chart 170
- Specifications 175
- Error Message List 177
- IMPORTANT SAFETY INSTRUCTIONS 179
- SAVE THESE INSTRUCTIONS 179
Produits connexes et manuels pour Matériel d'enregistrement Roland MC-4
(26 pages)
(84 pages)
(274 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.720 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels