Roland MC-4 Manuel du propriétaire télécharger pdf (Page 139)

139

About V-LINK

V-LINK

V-LINK settings

Resetting the image

* For details on clips/palettes, dissolve time, color difference signals (Cb/

Cr), refer to the Edirol DV-7PR manual.

The MC-909 does not support the Edirol DV-7PR’s dual stream

mode.

Parameter

Range Explanation

Note Tx Ch

1–16 MIDI channel that will switch Edirol DV-7PR clips/palettes and will control dissolve time.

Clip 1 Note No. 0(C-1)–127(G9) Note number (velocity pad) that corresponds to Edirol DV-7PR clip 1

If this is set to 59 (B3), velocity pads 1–16 will correspond to clips 1–16.

Play Speed Ctrl 0.0–1.0–2.0, 0.5–1.0–2.0,

0.0–1.0–4.0, 0.5–1.0–4.0,

0.0–1.0–8.0, 0.5–1.0–8.0,

0.0–1.0–16.0, 0.5–1.0–16.0,

0.0–1.0–32.0, 0.5–1.0–32.0,

0.0–2.0–4.0, 0.0–4.0–8.0,

0.0–8.0–16.0, 0.0–16.0–32.0,

-2.0–1.0–4.0, -6.0–1.0–8.0

Range of video playback speed

The three values are the playback speeds (multiples of normal speed) at the negative,

center, and positive positions of the turntable emulation slider.

Dissolve Time OFF, CC1, CC5, CC7, CC10,

CC11, CC71–74, CC91–93,

Channel Aftertouch

Control change number that controls the dissolve time (time over which the image switch-

es)

Ctrl Tx Ch 1–16 MIDI channel that will control the Edirol DV-7PR color Cb/Cr, brightness, and video effect

switching

Color Cb Ctrl OFF, CC1, CC5, CC7, CC10,

CC11, CC71–74, CC91–93,

Channel Aftertouch

Control change number that controls the Cb color of the image

Color Cr Ctrl Control change number that controls the Cr color of the image

Brightness Ctrl Control change number that controls the brightness of the image

VFX1–4 Ctrl Control change number that controls the video effect

* VFX2–4 are not supported by the Edirol DV-7PR.

Fade Ctrl Control change number that controls the output fade

PAD MODE CLIP, PALETTE Selects whether the velocity pads will switch clips or palettes.

Press [F1 (Clip mode)]:

switch clips

Press [F2 (Palette)]:

switch palettes

Local Sw OFF, ON Specifies whether the internal sound generator is disconnected (OFF) from the velocity

pads, or not (OFF).

Clip filter

(check boxes 1–32)

(OFF),

✔

(ON) Enable/disable switching for each clip

Clips that are checked can be switched (see explanatory box below)

Using the Clip Filter

For example, suppose that of the rhythm set you input in the

part used for V-LINK (i.e., the part of the same number as the

Note Tx Channel), you want only the kick and snare to switch

clips. In this case, check only the clips that correspond to the

note numbers of the kick and snare. The clips will switch when

the kick or snare plays.

[F3 (Clip Reset)] Turn off the image (solid black).

[F4 (All Reset)] The effect applied to the image will be reset,

and brightness, color difference, etc. will all

return to the default value.

MC-909_Ref_e.book 139 ページ２００５年６月２８日　火曜日　午後２時５３分

1 2 ... 134 135 136 137 138 139 140 141 142 143 144 ... 179 180

Commentaires sur ces manuels

Pas de commentaire

Roland MC-4 Manuel du propriétaire Page 139

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel d'enregistrement Roland MC-4