Part 2
61
<A>
Accessories ....................................................................... 11
Application software ........................................................ 32
Arrow keys ....................................................................... 13
“AUTO” (COMMAND selection) ............................. 32, 41
“AUTO” (I/O selection) ............................................. 19, 41
Adhesive sheet ............................................................ 11, 20
<B>
Baud rate..................................................................... 19, 41
“BAUDRATE”............................................................ 19, 41
Bellows ............................................................................. 43
“BUFFER EMPTY” ......................................................... 50
<C>
CAMM-GL I .............................................................. 32, 51
CAMM-GL I Programmer’s Manual................................ 51
CD-ROM .............................................................. 11, 16, 17
Centronics ............................................................. 15, 19, 59
Character cutter .......................................................... 11, 59
Chip cleaning .............................................................. 33, 43
Clamps ........................................................................ 11, 20
Cleaning............................................................................ 43
- Cleaning the after operation .................................... 33, 43
- Cleaning the main unit .................................................. 43
Clear ........................................................................... 37, 40
“CLEAR” ................................................................... 37, 40
Collet .......................................................................... 11, 21
“COMMAND” ................................................................. 42
Compatible Software ........................................................ 16
Connection........................................................................ 15
- Computer connection .................................................... 15
- Power cord connection .................................................. 15
- Vacuum cleaner connection ........................................... 26
Connection parameters ..................................................... 19
“CONTINUE” (pause state) ............................................. 39
Coordinate value............................................................... 40
Cover ................................................................................ 12
Crossover serial cable ....................................................... 15
Cutter .............................................................. 11, 21, 30, 58
Cutter holder ............................................................... 11, 21
- Installing the cutter holder and collet ............................ 21
Cutter down key................................................................ 13
Cutter down position ........................................................ 31
Cutter up key .................................................................... 13
Cutter up position ............................................................. 31
Cutting area ...................................................................... 35
Cutting condition .............................................................. 28
Cutting-in amount........................................... 23, 28, 29, 30
Index
<D>
“DATA” ...................................................................... 19, 41
Data bits ...................................................................... 19, 41
Data buffer ........................................................................ 37
Depth regulator nose................................. 11, 12, 22, 23, 24
Device control instructions ............................................... 54
Display menus ............................................................ 40, 56
Driver ........................................................................... 17,18
Display menus flowchart .................................................. 56
Double-sided tape ............................................................. 21
<E>
EMERGENCY STOP switch ........................................... 13
“EMERGENCY STOP” ................................................... 50
ENTER/PAUSE key ......................................................... 13
Error messages.................................................................. 49
External output connector........................................... 12, 60
<F>
Feed rate ............................................................... 28, 30, 40
Flowchart (display menus) ............................................... 56
<H>
“HANDSHAKE”........................................................ 19, 41
Head.................................................................................. 12
Help .................................................................................. 18
Hexagonal screw driver .................................. 11, 23, 24, 34
“HOME” ........................................................................... 40
Home position .................................................................. 27
<I>
“I/O” ........................................................................... 19, 41
Installation ........................................................................ 14
Installing the Software...................................................... 16
- Installing the DRIVER .................................................. 17
Instruction system....................................................... 32, 51
Interface specifications ..................................................... 59
Interface type ........................................................ 15, 19, 41
<L>
Labels ............................................................................. 5, 9
Language .......................................................................... 36
Liquid-crystal display ....................................................... 13
Loading
- Loading a cutter............................................................. 21
- Loading a workpiece ..................................................... 20
Lock-use pin ..................................................................... 15
<M>
Maintenance ..................................................................... 43
Maximum cutting area................................................ 35, 59
MENU key........................................................................ 13
mode1 ............................................................................... 51
mode2 ............................................................................... 52
Motor brushes ............................................................. 11, 44
Commentaires sur ces manuels