Roland GT-PRO Manuel du propriétaire télécharger pdf (Page 53)

Chapter 4 Introduction to Effects and Parameters

Chapter 4

When Type is Set to S/R1→S/R2 or S/R1&S/R2

PRE LOOP

You can connect an external effects processor to the PRE

LOOP SEND/RETURN jacks and use it as one of the GT-

PRO’s effects.

This is convenient when you want to have distortion, wah, or

other external effects processors connected ahead of the

effects chain (p. 22).

Switch PRE LOOP on and off by pressing [PRE LOOP].

• You cannot change the connection sequence in PRE

LOOP. Effects are always connected ahead of the front

panel INPUT LEVEL knob.

• Guitar synths, the Harmonist effect, and other effects

that use processes requiring detection of performance

data may not function properly when PRE LOOP is

switched on with distortion effects connected to PRE

LOOP.

• PRE LOOP is unavailable when the Input Select (p. 90, p.

96) parameter is set to “USB In.”

Parameter/

Range

Explanation

Select

S/R1, S/R2,

S/R1&S/R2

This selects how SEND/RETURN 1 and

SEND/RETURN 2 are used.

S/R1

Only SEND/RETURN 1 are used.

S/R2

Only SEND/RETURN 2 are used.

S/R1&S/R2

Both SEND/RETURN 1 and SEND/RETURN 2 are used.

Mode 1

Normal, Direct Mix,

Branch Out

Switches the SEND/RETURN 1 mode.

Normal

Outputs the input to LOOP to the SEND 1 jack and the input from

the RETURN 1 jack to the circuit post-LOOP.

Use this when you want to connect an external effects device serially

in the GT-PRO’s effects chain.

Direct Mix

Outputs the input to LOOP to the SEND 1 jack, mixes the input from

the RETURN 1 jack with the input to LOOP (the direct sound), then

outputs this to the circuit post-LOOP. Use this when you want to mix

the GT-PRO’s effects sounds together with the sound with the exter-

nal effects device applied to it.

Branch Out

outputs the input to LOOP to the SEND 1 jack. The input from the

RETURN 1 jack is disregarded. For example, using this with the GT-

PRO’s reverb and delay immediately ahead of the loop allows you to

use the SEND 1 jack as a direct out.

Send 1 Level

0–200

Adjusts the volume of the output to the ex-

ternal effects device.

Return 1 Level

0–200

Adjusts the volume of the input from the ex-

ternal effects device.

Mode 2

Normal, Direct Mix,

Branch Out

Switches the SEND/RETURN 2 mode.

Normal

Outputs the input to LOOP to the SEND 2 jack and the input from

the RETURN 2 jack to the circuit post-LOOP.

Use this when you want to connect an external effects device serially

in the GT-PRO’s effects chain.

Direct Mix

Outputs the input to LOOP to the SEND 2 jack, mixes the input from

the RETURN 2 jack with the input to LOOP (the direct sound), then

outputs this to the circuit post-LOOP. Use this when you want to mix

the GT-PRO’s effects sounds together with the sound with the exter-

nal effects device applied to it.

Branch Out

outputs the input to LOOP to the SEND 2 jack. The input from the

RETURN 2 jack is disregarded. For example, using this with the GT-

PRO’s reverb and delay immediately ahead of the loop allows you to

use the SEND 2 jack as a direct out.

Send 2 Level

0–200

Adjusts the volume of the output to the ex-

ternal effects device.

Return 2 Level

0–200

Adjusts the volume of the input from the ex-

ternal effects device.

Parameter/

Range

Explanation

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 163 164

Commentaires sur ces manuels

Pas de commentaire

Roland GT-PRO Manuel du propriétaire Page 53

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement musical supplémentaire Roland GT-PRO