Roland GT-PRO Manuel du propriétaire télécharger pdf (Page 16)

Chapter 1 Playing Sounds

* To prevent malfunction and/or damage to speakers or other

devices, always turn down the volume, and turn off the power

on all devices before making any connections.

* Raise the amp volume only after turning on the power to all

connected devices.

* When outputting in mono, connect the cable to the MAIN

OUT L (MONO) jack.

* Use only the specified expression pedal (Roland EV-5 or

Roland FV-300L; sold separately). By connecting any other

expression pedals, you risk causing malfunction and/or

damage to the unit.

* This instrument is equipped with balanced (XLR) type

connectors. Wiring diagrams for these connectors are shown

below. Make connections after first checking the wiring

diagrams of other equipment you intend to connect.

fig.XLRJack

* When using the unit with an expression pedal connected to the

EXP PEDAL 1 and EXP PEDAL 2 jack, set Minimum

Volume to the “MIN” position.

* When using the unit with a foot switch (the optional FS-6)

connected to the CTL 1/2 jack and CTL 3/4 jack, set the

MODE switch and POLARITY switch as shown below.

fig.01-0020

* When using the unit with a foot switch (the optional FS-5U)

connected to the SUB EXP PEDAL/SUB CTL 1,2 jack, set the

polarity switch as shown below.

fig.01-0030

* You can use the special (optional Roland) PCS-31 connector

cord to connect two foot switches.

fig.01-0040

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

• When using the unit with the EXP pedals connected to

the EXP PEDAL 1 jack and EXP PEDAL 2 jack, make

the settings given on p. 63 and p. 65.

• When using the unit with the foot switches connected

to the CTL 1/2 jack and CTL 3/4 jack, make the

settings given on p. 62.

• For more on using the AMP CTL 1 jack and AMP CTL 2

jack, refer to p. 54.

• For more on using the LOOP 1/2 SEND/RETURN

jacks, refer to p. 52.

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Turning on the Power

Once the connections have been completed (p. 15), turn on

power to your various devices in the order specified. By

turning on devices in the wrong order, you risk causing

malfunction and/or damage to speakers and other devices.

1. Before turning on the power, confirm the following.

• Are all external devices properly connected?

• Is the volume on the GT-PRO, your amp, and all other

connected devices turned down to the minimum level?

2. Switch ON the POWER switch on the GT-PRO’s front

panel.

The display changes, showing the following. A few

seconds later, the unit enters the ordinary performance

mode.

The screen that appears at this point is called the

“Play screen.”

fig.01-0050d

* Upon power-up, the patch most recently selected when the

power was last turned off is selected.

* This unit is equipped with a protection circuit. A brief interval

(a few seconds) after power up is required before the unit will

operate normally.

3. Next, turn on the power to any external effects

processors, then to the guitar amp (power amp).

Polarity Switch

PCS-31

White Red

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 163 164

Commentaires sur ces manuels

Pas de commentaire

Roland GT-PRO Manuel du propriétaire Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement musical supplémentaire Roland GT-PRO