Roland GT-PRO Manuel du propriétaire Page 103
- Page / 164
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
103
Appendices
Appendices
Restoring the Factory
Settings (Factory Reset)
Restoring the GT-PRO to the settings made at the factory is
referred to as “Factory Reset.”
Not only can you return all of the settings to the values in
effect when the GT-PRO was shipped from the factory, you
can also specify the range of settings to be reset.
fig.11-0010
1. Turn off the power.
2. While holding down PREAMP/SPEAKER On/Off
button and [TYPE VARIATION], turn on the power.
The Factory Reset range setting screen appears in the
display.
fig.11-0020d
* To cancel Factory Reset, press [EXIT].
3. Press PARAMETER [ ] [ ] to move the cursor,
and rotate the PATCH/VALUE dial to specify the range
of settings you want to restore to factory settings.
4. If you want to proceed with the factory reset, press
[ENTER].
The specified range of data will be returned, and return
to the Play screen.
List of Factory Settings
value Explanation
System
System parameters, Harmonist scales, Auto Riff phrases, and
Preamp/Speaker, Overdrive/Distortion, and Wah Custom Edit
parameter settings
Quick
Content of the Settings Made with User Quick Setting
#1-1–#20-10
Settings for Patch Number 1-1 through 20-10
3
1
42
The range of data you wish to factory reset
Parameter Value
TUNER
TUNER Pitch A= 440Hz
TUNER Out Bypass
OUTPUT SELECT
MAIN Output Sel. LINE/PHONES
MAIN Low EQ 0dB
MAIN Mid EQ 0dB
MAIN Mid Freq 500Hz
MAIN High EQ 0dB
TOTAL NS Thres 0dB
TOTAL Rev Level 100%
SUB Output Sel. LINE/PHONES
SUB Low EQ 0dB
SUB Mid EQ 0dB
SUB Mid Freq 500Hz
SUB High EQ 0dB
Output Channel PATCH
USB/DGT Out Ch. MAIN
USB/DGT Out Lev 100
USB Mix Channel MAIN
USB Mix Level 100
SYSTEM
LCD Contrast 16
Input Select Guitar In
Input Level 0dB
Input Pres. 0dB
P.Chnge Mode Fast
Preamp Mode Patch
Patch Extent P40-10
Assign Hold On
Knob Mode Immediate
EXP1 Func Auto
CTL1 Func Assignable
CTL2 Func Assignable
EXP2 Func Assignable
CTL3 Func Assignable
CTL4 Func Assignable
CC#7 Func Auto
CC#80 Func Assignable
CC#1 Func Assignable
Main Out Lev +4dBu
Sub Out Lev +4dBu
LP Send Lev -10dBu
LP Retrn Lev -10dBu
FC-200
Mode Off
Ctl Pedal Momentary
Bank Lmt 39
PC Out Wait for a NUM.
Bank Chng Bank Pedal Only
- Owner’s Manual 1
- USING THE UNIT SAFELY 3
- IMPORTANT NOTES 5
- Contents 7
- Installing & 9
- Main Features 10
- Front Panel 11
- Rear panel 13
- Signal Flow 14
- Chapter 1 Playing Sounds 15
- Turning on the Power 16
- Adjusting the Input Level 17
- Adjusting the Output Level 17
- Turning Off the Power 18
- What is a Patch? 19
- How to Switch Patches 19
- (Patch Change) 19
- Turning the Effect On and Off 20
- Setting the Effects Simply 21
- (QUICK FX) 21
- Changing the Connection 22
- Naming Patches (Patch Name) 23
- Copying Patches (Patch Copy) 24
- Exchanging Patches 25
- (Patch Exchange) 25
- Initializing Patches 25
- Storing Settings by Effect 26
- (User Quick Settings) 26
- Copying the PREAMP/SPEAKER 27
- Settings to Another Channel 27
- PREAMP/SPEAKER (Preamp/ 28
- Speaker Simulator) 28
- Chapter 4 29
- Type List 30
- OVERDRIVE/DISTORTION 31
- OUTPUT L 32
- OUTPUT R 32
- Using the HOLD (Hold Delay) 34
- COMP (Compressor) 35
- FX-1/FX-2 36
- AW (Auto Wah) 38
- TM (Tone Modify) 38
- GS (Guitar Simulator) 38
- FL (Flanger) 40
- VB (Vibrato) 40
- STR (Sitar Simulator) 42
- FB (Feedbacker) 42
- WSY (Wave Synth) 44
- SEQ (Sub Equalizer) 44
- PS (Pitch Shifter) 46
- 2CE (2 x 2 Chorus) 48
- AR (Auto Riff) 48
- AC (Acoustic Processor) 50
- EQ (Equalizer) 51
- (External Effects Loop) 52
- PRE LOOP 53
- AMP CTL (Amp Control) 1/2 54
- FX CHAIN (Effect Chain) 56
- NAME (Patch Name) 56
- Chapter 5 57
- Customizing the Speakers 58
- Customizing 59
- Overdrive/Distortion 59
- Customizing Pedal Wah 60
- Use-Specific Guide 61
- PCS-31PCS-31 62
- Red WhiteRed White 62
- EXP Pedal (EXP1, 2 Function) 63
- Chapter 6 65
- Quick Settings 66
- Target Range 68
- Internal Pedal System 70
- Chapter 7 72
- Transmitting and Receiving 75
- MIDI Data 75
- MIDI Device (Bulk Load) 76
- Changing Patch Numbers on an 78
- About MIDI 79
- About the MIDI implementation 80
- Chapter 8 81
- GT-PRO to the FC-200 82
- Controlling the GT-PRO with 83
- EXP Pedal CC#7 CC#7 Function 84
- Pedal Connected to the 84
- FOOT SW/EXP 1 Jack 84
- CC#1 CC#1 Function 84
- Advanced Settings 86
- Before Connecting with USB 88
- Setting USB-Related Functions 89
- Recording the GT-PRO’s 90
- Output with a Computer 90
- Running the GT-PRO from a 91
- Computer 91
- Adjusting the overall sound 94
- Adjusting the Display 96
- Contrast (LCD Contrast) 96
- Switching the Sounds Input 96
- Switched (Patch Extent) 98
- Setting the Knob Functions 99
- (Knob Mode) 99
- Checking the Effect Level 100
- Chapter 10 101
- Chapter 10 Other Features 102
- Appendices 103
- MIDI Implementation Chart 105
- Specifications 106
- ■ Mac OS 108
- ■ Windows 108
- ■ What is USB Driver? 109
- About the Driver Modes 110
- Installing the Special Driver 111
- System icon may be displayed 113
- Windows 2000 users 114
- Windows Me/98 users 117
- Windows XP/2000 users 118
- Windows Me users 119
- Windows 98 users 120
- Driver settings 123
- Input/output device settings 124
- Software settings 125
- Mac OS 9 users 129
- OMS settings 130
- FreeMIDI settings 133
- Installing the ASIO driver 135
- Mac OS X users 136
- Adjusting the audio latency 141
- Using ASIO Direct Monitor 141
- If using Windows: 142
- If using Macintosh: 142
- Troubleshooting 143
- Other Problems 144
- Problems when using the 147
- USB Driver 147
- Deleting the Special Driver 151
- Patch List 152
- ■ Preset Patch 156
- IMPORTANT SAFETY INSTRUCTIONS 163
- SAVE THESE INSTRUCTIONS 163
Produits connexes et manuels pour Équipement musical supplémentaire Roland GT-PRO
(184 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.793 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels