Roland GT-PRO Manuel du propriétaire télécharger pdf (Page 35)

Chapter 4 Introduction to Effects and Parameters

Chapter 4

REVERB

This effect adds reverberation to the sound.

COMP (Compressor)

This is an effect that produces a long sustain by evening out

the volume level of the input signal. You can switch it to a

“limiter” to suppress only the sound peaks and prevent

distortion.

Parameter/

Range

Explanation

On/Off

Off, On Turns the REVERB effect on/off.

Type

see below

This selects the reverb type. Various differ-

ent simulations of space are offered.

Ambience

Simulates an ambience mic (off-mic, placed at a distance from the

sound source) used in recording and other applications. Rather than

emphasizing the reverberation, this reverb is used to produce a sense

of openness and depth.

Room

Simulates the reverberation in a small room. Provides warm rever-

berations.

Hall1

Simulates the reverberation in a concert hall. Provides clear and spa-

cious reverberations.

Hall2

Simulates the reverberation in a concert hall. Provides warm rever-

berations.

Plate

Simulates plate reverberation (a reverb unit that uses the vibration of

a metallic plate). Provides a metallic sound with a distinct upper

range.

Spring

This simulates the sound of a guitar amp's built-in spring reverb.

Modulate

This reverb adds the wavering sound found in hall reverb to provide

an extremely pleasant reverb sound.

Reverb Time

0.1 sec–10.0 sec Adjusts the length (time) of reverberation.

Pre Delay

0 msec–100 msec

Adjusts the time until the reverb sound ap-

pears.

Low Cut (Low Cut Filter)

Flat, 55 Hz–800 Hz

This sets the frequency at which the low cut

filter begins to take effect.

This lets you cut the low-end component below the set frequency to

create a clear, distinct low end, thereby bringing out the high end of

the effect. When “Flat” is selected, the low cut filter will have no ef-

fect.

High Cut (High Cut Filter)

700 Hz–11.0 kHz, Flat

This sets the frequency at which the high cut

filter begins to take effect.

This allows you to get a mild effect sound by cutting the high-end

component above the set frequency. When “Flat” is selected, the

high cut filter will have no effect.

Density

0–10 Adjusts the density of the reverb sound.

Effect Level

0–100 Adjusts the volume of the reverb sound.

Direct Level

0–100 Adjusts the volume of the direct sound.

Parameter/

Range

Explanation

On/Off

Off, On Turns the COMP effect on/off.

Type

Compressor, Limiter

This selects whether the compressor or lim-

iter is used.

Sustain (Type= Compressor)

0–100

Adjusts the range (time) over which low-

level signals are boosted. Larger values will

result in longer sustain.

Attack (Type= Compressor)

0–100

Adjusts the strength of the picking attack

when the strings are played.

Higher values result in s sharper attack, creating a more clearly de-

fined sound.

Threshold (Type= Limiter)

0–100

Adjust this as appropriate for the input sig-

nal from your guitar.

When the input signal level exceeds this threshold level, limiting will

be applied.

Release (Type= Limiter)

0–100

Adjusts the time from when the signal level

drops below the threshold until when limit-

ing is removed.

Tone

-50–+50 Adjusts the tone.

Level

0–100 Adjusts the volume.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 163 164

Commentaires sur ces manuels

Pas de commentaire

Roland GT-PRO Manuel du propriétaire Page 35

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement musical supplémentaire Roland GT-PRO