Roland CM-500 Spécifications Page 62
- Page / 80
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
60
Menu Function Range Default
SETTING
VS CMD To perform cutting at the speed determined by a VS DISABLE/ENABLE DISABLE
COMMANDS
command (tool speed setting command) sent from the
computer, set this to [ENABLE]. When set to
[DISABLE], cutting is performed using the values for
[**cm/s] at the cutting conditions screen and [UPSPEED].
!FS CMD To perform cutting at the blade force determined by an DISABLE/ENABLE DISABLE
FS command (tool force setting command) sent from
the computer, set this to [ENABLE]. When set to
[DISABLE], cutting is performed using the values for
[**gf] at the cutting conditions screen.
SP CMD This is normally set to [DISABLE] when performing DISABLE/ENABLE DISABLE
a cutting. When a tool-selection instruction (SP
instruction) is sent from the computer while this is set to
[DISABLE], the SP instruction is ignored and operation
continues without pause. When set to [ENABLE], SP
exchange instructions are accepted and operation
pauses. If tool change is needed, change the tool, then
press the [ENTER] key.
OTHERS
SMOOTHING
If you want the curves of circles and arcs to be cut ON/OFF ON
smoothly, set this to [ENABLE]. When on, however,
small text or intricate designs may also be cut with
rounded corners. If this happens, change the setting to
[DISABLE] and perform cutting again.
UNIT Select the unit of measurement for numerical values mm/ mm
shown on the display. inch
However, values are shown in metrics for the following
menus even when inch is selected.
FACTORY
This returns the settings values of the menu items to PRESET –
DEFAULT their factory-default values.
SELF TEST This adjusts the respective distances of the X axis. ––
Compare the actual measurements of the cutting
results with the data sent from the computer to
calculate and set the distance adjustment value.
CONTRAST This changes the contrast of the display. 5 to 1 5
TEST This changes the cutting-test pattern carried out when TYPE1/TYPE2 TYPE1
PATTERN you press the [TEST] key.
This performs an ordinary cutting test with [TYPE 1].
For thin materials or cases where graphics are too
small to obtain good cutting results with [TYPE 1],
make the setting for [TYPE 2].
TYPE 1 TYPE 2
- For Canada 2
- For the USA 2
- Table of Contents 3
- To Ensure Safe Use 4
- Warning Labels 8
- To Ensure Safe Use 9
- ATTENTION 11
- PRUDENCE 11
- Main unit 15
- 2 Part Names and Functions 17
- 1 Checking Supplied Items 17
- 2-2 Rear View 18
- 2-3 Operation Panel 18
- 3 Basic Operation 19
- Loading Roll Material 20
- Material Loading Position 21
- Rear View 24
- 3-2 Installing a Blade 25
- Cutting Test 26
- Blade Force 27
- 3-4 Setting the Origin Point 28
- 3-5 Starting Cutting 29
- To Sever the Material 30
- Pausing Cutting Operations 30
- Downloading Cutting Data 30
- Remove the Material 32
- Amount of 33
- Max. : 2.5 mmMin. : 0 mm 33
- 4 Advanced Operation 33
- Setting range: 34
- 0.025 mm) 34
- Settings for Cutting Quality 35
- (1-3/16 in.) 37
- Pinch Roller 37
- Material 37
- Coordinate Rotation Settings 38
- About the Cutting Area 39
- Roll material 40
- Material, Etc.) 41
- 4-6 Front Loading 43
- Tool location 45
- 4-7 The Overcut Feature 46
- 4-8 The Memory Feature 47
- Calling Up 48
- Deleting Settings 48
- 4-9 The Crop Mark Feature 49
- 4. Perform cutting 51
- Origin Point 52
- Offset Directtion 52
- 0.25 mm (0.01 in.) 53
- 5-2 About Special Materials 54
- [ ] Key 55
- [ ] Key [ENTER] Key 55
- [ ] [ ] Key 55
- 6 Descriptions of Features 55
- 6-2 Display Menus Flowchart 56
- COMMAND DISABLE 57
- SAVE USER 1 58
- 6-3 List of Functions 59
- Description of Menu Items 60
- TYPE 1 TYPE 2 62
- 7 Maintenance 65
- 7-2 Consumable Items 66
- 8 If There Is a Problem 69
- 8-2 What to do if 70
- The carrier paper is cut 72
- 8-3 Error Messages 74
- 9 Specifications 75
- 9-2 Specifications 76
- Pin number Signal Remark 78
- 1 VCC Cable power 78
- 2 - Data 78
- 3 + Data 78
- 4 GND Cable ground 78
- R1-060421 80
Produits connexes et manuels pour Matériel d'enregistrement Roland CM-500
(108 pages)
(254 pages)
(64 pages)
(65 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.149 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels