Roland GT-8 Manuel du propriétaire Page 91
- Page / 108
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
91
Appendices
Appendices
List of Factory Settings
Adjusting the EXP Pedal
Although the GT-8’s EXP pedal has been set for optimum
operation at the factory, extended use and the operating
environment can result in the pedal going out of adjustment.
If you encounter problems such as being unable to fully cut
off the sound with the volume pedal, you can use the
following procedure to readjust the pedal.
1.
Hold down ASSIGN [CTL/EXP] while you switch on
the power.
The following messages alternate in the display.
fig.09-040d
2.
With the pedal completely released, press [WRITE].
The message “- - - OK! - - -” appears, and then the
following messages alternate in the display.
fig.09-050d
* If you press [WRITE] when the pedal is not completely
released, or when the pedal position (angle) is not correct, the
message “- Area Over! -” appears in the display, and you are
prevented from proceeding to the next step If this occurs,
readjust the pedal position.
3.
With the pedal fully depressed, press [WRITE].
“- - - OK! - - -” appears, after this, the threshold
adjustment screen is displayed.
fig.09-051d
* If you press [WRITE] when the pedal is not fully depressed, or
when the pedal position (angle) is not correct, the message
“- Area Over! -” appears in the display, and you are prevented
from proceeding to the next step. If this occurs, readjust the
pedal position.
4.
Rotate the PATCH/VALUE dial to adjust the threshold.
Setting a lower value causes the EXP pedal switch to be
activated even when it is pressed lightly. When set to a
high value, the EXP pedal switch is activated only when
the pedal is pressed firmly.
5.
Press [WRITE].
The message “Press [EXIT]” appears.
6.
Press [EXIT].
After the message “Checking data please wait...” has
been displayed, you’ll be returned to the Play screen.
Parameter
Value
TUNER
Tuner Pitch
A= 440Hz
Tuner Out
Bypass
OUTPUT SELECT
Output Select
JC-120
GLOBAL Low EQ
0 dB
GLOBAL Mid EQ
0 dB
GLOBAL Mid Freq
500 Hz
GLOBAL High EQ
0 dB
TOTAL NS Thres
0 dB
TOTAL Rev Level
100%
SYSTEM
LCD Contrast
16
Input Level
0 dB
Input Pres.
0 dB
P.Chnge Mode
Fast
Preamp Mode
Patch
BANK Extent
85
Bnk Chg Mode
Wait for a NUM.
EXP Pdl Hold
On
Dial Func
PATCH No. & VALUE
Knob Mode
Immediate
Numbr Pdl SW
Off
Dgtl Out Lev
100%
CTL Pdl Func
Assignable
EXP SW Func
Assignable
EXP Pdl Func
Auto
SubCTL1 Func
Assignable
SubCTL2 Func
Assignable
Sub EXP Func
Assignable
MIDI
MIDI RX Channel
1
MIDI Omni Mode
Omni On
MIDI TX Channel
Rx
MIDI Device ID
1
MIDI Sync Clock
Auto
MIDI PC OUT
On
MIDI EXP OUT
CC#7
MIDI EXP SW OUT
CC#81
MIDI CTL OUT
CC#80
MIDI SubCTL1 OUT
Off
MIDI SubCTL2 OUT
Off
MIDI Map Select
Fix
MANUAL mode
1
A/B (Preamp Channel A/B)
2
OD
(OVERDRIVE/DISTORTION)
3
DD (DELAY)
4
CE (CHORUS)
▲
FX-2
▼
FX-1
GT-8_e.book 91 ページ ２００６年７月２５日 火曜日 午後１時４９分
- Owner’s Manual 1
- IMPORTANT NOTES 4
- Contents 5
- Main Features 8
- Front Panel 9
- Rear Panel 12
- Chapter 1 Playing Sounds 13
- Device (Amp) (Output Select) 14
- Turning Off the Power 15
- Switching Only the Number 16
- Switching the Bank and Number 17
- Turning the Effect On and Off 18
- Naming Patches (Patch Name) 21
- Copying Patches (Patch Copy) 22
- Destination User Patch 23
- Storing Settings by Effect 24
- (User Quick Settings) 24
- Copying the PREAMP/SPEAKER 25
- Settings to Another Channel 25
- PREAMP/SPEAKER (Preamp/ 26
- Speaker Simulator) 26
- Type List 28
- OVERDRIVE/DISTORTION 29
- OUTPUT L 30
- OUTPUT R 30
- Using the HOLD (Hold Delay) 31
- COMP (Compressor) 33
- FX-1/FX-2 34
- TR (Tremolo) 37
- PH (Phaser) 37
- STR (Sitar Simulator) 40
- FB (Feedbacker) 40
- WSY (Wave Synth) 42
- SEQ (Sub Equalizer) 42
- HR (Harmonist) 43
- PS (Pitch Shifter) 44
- 2CE (2 x 2 Chorus) 46
- AR (Auto Riff) 46
- AC (Acoustic Processor) 48
- EQ (Equalizer) 49
- LOOP (External Effects Loop) 50
- AMP CTL (Amp Control) 50
- When the pedal 51
- Use-Specific Guide 53
- Setting the Operation of the 54
- Quick Settings 57
- Manual Settings 58
- When using the foot switch: 59
- When using the EXP pedal: 59
- EXP pedal: 60
- Setting Assign Input Sens 60
- Internal Pedal System 61
- Wave Pedal 62
- Chapter 6 63
- Customizing the Speakers 64
- Customizing 65
- Overdrive/Distortion 65
- Customizing Pedal Wah 66
- Chapter 7 Other Features 67
- (Example) 68
- Input Level 70
- Input Pres. (Input Presence) 70
- Setting the System Preamp 71
- Limiting the Banks That Can 72
- Be Switched (Bank Extent) 72
- Selecting the PATCH/VALUE 73
- Dial Function (Dial Function) 73
- DIGITAL IN 75
- Tuning the Guitar 76
- On and Off With the Pedals 78
- Chapter 8 79
- Making the Settings for MIDI 80
- Functions 80
- Transmitting and Receiving 81
- MIDI Data 81
- MIDI Device (Bulk Load) 82
- Error Messages 88
- Troubleshooting 89
- Restoring the Factory 90
- Settings (Factory Reset) 90
- Adjusting the EXP Pedal 91
- MIDI Implementation Chart 92
- Specifications 93
- Preset Patch 99
- Patch List 100
- Appendices 101
- Apparatus containing 107
- Lithium batteries 107
Produits connexes et manuels pour Pianos numériques Roland GT-8
(2 pages)
(64 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.317 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels