Roland GT-8 Manuel du propriétaire Page 71
- Page / 108
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
71
Chapter 7 Other Features
Chapter
7
Keeping Effect Sounds Playing After Patches
Are Switched (Patch Change Mode)
The GT-8 features a mode that is enabled when spatial effects
(such as reverb and delay) are used, whereby the effects
sound of one patch continues playing even after you switch
to the next patch. If the necessary conditions regarding the
effects chain and effect parameter settings are met, you can
then have the decay of reverb, delay, and similar effects
continue on into the next patch after you switch patches.
• Effects are in the same effects chain
• When switching the delay off or on, or when the type
and time are identical
• When switching other effects off or on, or when the
parameter settings are identical
* There still may be no reverberation in some cases, even after
the above settings are made.
fig.07-111
1.
Press [SYSTEM], then press PARAMETER [ ]
[ ] so that “SYS: P.Chnge Mode” is displayed.
fig.07-120d
2.
Rotate the PATCH/VALUE dial to change the setting’s
value.
3.
Press [EXIT] to return to the Play screen.
Using the Identical Preamp Settings
in All Patches (Preamp Mode)
With the GT-8, you can have a preamp be set globally for use
in all patches.
This provides an effect that always gives you the sound of
the same guitar amp regardless of the patches you set.
fig.07-121
1.
Press [SYSTEM], then press PARAMETER [ ]
[ ] so that “SYS: Preamp Mode” is displayed.
fig.07-130d
2.
Rotate the PATCH/VALUE dial to change the setting’s
value.
3.
Press [EXIT] to return to the Play screen.
Setting the System Preamp
When the Preamp Mode is set to System, preamp settings
made by adjusting the panel controls are treated as system
preamp settings.
The stored content is updated each time the settings are
changed.
Value
Explanation
Fast
Patches are changed normally. The unit switches to the subse-
quent patch without any carry-over of the decay from the pre-
vious patch’s reverb or chorus.
Smooth
The unit switches to the subsequent patch with the decay from
the previous patch’s reverb or delay continued after the switch
is made.
* For smooth switching, patches may be switched with one tempo
delayed.
1
21
3
Value
Explanation
Patch
The patch preamp setting is used. This al-
lows you to use different preamp settings
in each individual patch.
System
The system’s preamp setting is used. This
applies the same preamp settings to all
patches.
1
21
3
GT-8_e.book 71 ページ ２００６年７月２５日 火曜日 午後１時４９分
- Owner’s Manual 1
- IMPORTANT NOTES 4
- Contents 5
- Main Features 8
- Front Panel 9
- Rear Panel 12
- Chapter 1 Playing Sounds 13
- Device (Amp) (Output Select) 14
- Turning Off the Power 15
- Switching Only the Number 16
- Switching the Bank and Number 17
- Turning the Effect On and Off 18
- Naming Patches (Patch Name) 21
- Copying Patches (Patch Copy) 22
- Destination User Patch 23
- Storing Settings by Effect 24
- (User Quick Settings) 24
- Copying the PREAMP/SPEAKER 25
- Settings to Another Channel 25
- PREAMP/SPEAKER (Preamp/ 26
- Speaker Simulator) 26
- Type List 28
- OVERDRIVE/DISTORTION 29
- OUTPUT L 30
- OUTPUT R 30
- Using the HOLD (Hold Delay) 31
- COMP (Compressor) 33
- FX-1/FX-2 34
- TR (Tremolo) 37
- PH (Phaser) 37
- STR (Sitar Simulator) 40
- FB (Feedbacker) 40
- WSY (Wave Synth) 42
- SEQ (Sub Equalizer) 42
- HR (Harmonist) 43
- PS (Pitch Shifter) 44
- 2CE (2 x 2 Chorus) 46
- AR (Auto Riff) 46
- AC (Acoustic Processor) 48
- EQ (Equalizer) 49
- LOOP (External Effects Loop) 50
- AMP CTL (Amp Control) 50
- When the pedal 51
- Use-Specific Guide 53
- Setting the Operation of the 54
- Quick Settings 57
- Manual Settings 58
- When using the foot switch: 59
- When using the EXP pedal: 59
- EXP pedal: 60
- Setting Assign Input Sens 60
- Internal Pedal System 61
- Wave Pedal 62
- Chapter 6 63
- Customizing the Speakers 64
- Customizing 65
- Overdrive/Distortion 65
- Customizing Pedal Wah 66
- Chapter 7 Other Features 67
- (Example) 68
- Input Level 70
- Input Pres. (Input Presence) 70
- Setting the System Preamp 71
- Limiting the Banks That Can 72
- Be Switched (Bank Extent) 72
- Selecting the PATCH/VALUE 73
- Dial Function (Dial Function) 73
- DIGITAL IN 75
- Tuning the Guitar 76
- On and Off With the Pedals 78
- Chapter 8 79
- Making the Settings for MIDI 80
- Functions 80
- Transmitting and Receiving 81
- MIDI Data 81
- MIDI Device (Bulk Load) 82
- Error Messages 88
- Troubleshooting 89
- Restoring the Factory 90
- Settings (Factory Reset) 90
- Adjusting the EXP Pedal 91
- MIDI Implementation Chart 92
- Specifications 93
- Preset Patch 99
- Patch List 100
- Appendices 101
- Apparatus containing 107
- Lithium batteries 107
Produits connexes et manuels pour Pianos numériques Roland GT-8
(2 pages)
(64 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels