Roland RD-700 Manuel d'utilisateur Page 15
- Page / 172
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
15
Getting Ready
Getting Ready
Installing the Wave Expansion Board
Up to two optional Wave Expansion Boards (SRX Series) can be installed in
the RD-700.
Wave Expansion Boards store Wave data, Patches, and Rhythm Sets, and by
equipping the RD-700 with these boards, you can greatly expand your
sound palette.
Cautions When Installing an Wave Expansion Board
●
To avoid the risk of damage to internal components that can be caused by
static electricity, please carefully observe the following whenever you
handle the board.
• Before you touch the board, always first grasp a metal object (such as
a water pipe), so you are sure that any static electricity you might
have been carrying has been discharged.
• When handling the board, grasp it only by its edges. Avoid touching
any of the electronic components or connectors.
• Save the bag in which the board was originally shipped, and put the
board back into it whenever you need to store or transport it.
●
Use a Philips screwdriver that is suitable for the size of the screw (a
number 2 screwdriver). If an unsuitable screwdriver is used, the head of
the screw may be stripped.
●
To remove a screw, rotate the screwdriver
counter-clockwise. To tighten a screw, rotate
the screwdriver clockwise.
●
Be careful that the screws you remove do not
drop into the interior of the RD-700.
●
Do not leave the rear panel cover removed. After installation of the Wave
Expansion Boards is complete, be sure to replace the cover.
●
Do not touch any of the printed circuit pathways or connection terminals.
●
Be careful not to cut your hand on the edge of the installation bay.
●
Never use excessive force when installing a circuit board. If it doesn’t fit
properly on the first attempt, remove the board and try again.
●
When circuit board installation is complete, double-check your work.
●
Always turn the unit off and unplug the power cord before attempting
installation of the circuit board.
●
Install only the specified circuit board(s) (SRX Series). Remove only the
specified screws.
Install the Wave Expansion Boards after removing the rear panel cover.
There are two slots (A and B) into which a board can be installed. Specify
which slot's board is to be used by pressing EXPANSION [A] or [B] on the
front panel when using waves, tones, or Rhythm Sets from the wave
expansion boards.
tightenloosen
RD-700_e.book 15 ページ ２００４年４月２６日 月曜日 午前１１時５４分
- Owner’s Manual 1
- USING THE UNIT SAFELY 3
- IMPORTANT NOTES 5
- Main Features 6
- Contents 10
- General MIDI 11
- General MIDI 2 11
- Panel Descriptions 12
- 12 13 14 13
- Rear Panel 14
- Getting Ready 15
- Installing SRX Series Boards 16
- Equipment 22
- Connecting Pedals 23
- Turning the Power On and Off 24
- Adjusting the Volume 25
- (Factory Reset) 26
- After performing a Factory 27
- Reset, you may need to re 27
- When this occur, adjust 27
- (LCD Contrast) 28
- (Master Tune) 29
- Overview of the RD-700 31
- About the CURSOR Buttons 33
- Changing the Settings Values 33
- Performing with the Keyboard 35
- ([NUM LOCK]) 37
- Playing a Rhythm Set 38
- To Switch to Single Mode 41
- You can change the split 43
- Please refer to “Changing 43
- Point” (p. 44) 43
- Parts (PART SWITCH/LEVEL) 45
- ([TRANSPOSE]) 46
- BENDER BENDER 48
- You Play ([ARPEGGIO]) 49
- Changing the Arpeggio Style 50
- Changing Arpeggio Tempos 50
- Playing Rhythm ([RHYTHM]) 51
- Changing the Rhythm Pattern 52
- Changing Rhythm Tempos 52
- (MULTI EFFECTS) 53
- 12,4,8 3,6 359,10 56
- Settings Not Saved in a Setup 58
- Setup <000> 58
- What’s MIDI? 59
- MIDI Send Channel Settings 60
- (MIDI TX Part) 62
- Detailed Settings for 63
- Transmitted Parts ([MIDI TX]) 63
- Master Keyboard 64
- (Piano Edit) 66
- Settings (EQ-SW/EQ Gain/ 67
- EQ Frequency/EQ Q) 67
- Parameters That Can Be Set 68
- Edit Mode 69
- Setting the Keyboard Touch 71
- (Key Touch) 71
- Pedal, [CONTROL] Knob, and 73
- Equalizer Settings 73
- (Control/EQ) 73
- Tones (Tone Wheel Mode) 75
- Setting the Multi-Effects 76
- Reverb, and Chorus Effects 76
- (MFX/Reverb/Chorus) 76
- Making Multi-Effects Settings 77
- Making Reverb Settings 78
- Setting Chorus and Delay 78
- How to Make Settings 79
- Making the Rhythm Settings 82
- (Rhythm Pattern) 82
- Making Arpeggio Settings 83
- (Arpeggio) 83
- 90 10 90 10 86
- 50 50 50 50 86
- (Internal Part Prm) 89
- Setting MIDI Receive Parts 89
- Other Functions (Utility) 92
- Connecting MIDI Devices 95
- Recording the Performance 96
- About the Local Switch 96
- Sound Generator from an 97
- External MIDI Device 97
- Using the RD-700 as a GM 98
- Sound Module (GM Mode) 98
- Troubleshooting 100
- Error Messages/Other Messages 103
- Effect/Parameter List 104
- Effects Parameter List 126
- Appendices 127
- Reverb Parameters 134
- Chorus Parameters 134
- Tone List 135
- Rhythm Set List 138
- Arpeggio Style List 142
- Rhythm Pattern List 143
- Setup List 144
- Shortcut List 145
- MIDI Implementation 146
- 2. Data Transmission 151
- 3. Parameter Address Map 153
- 4. GS (Model ID = 42H) 157
- MIDI Implementation Chart 162
- Main Specifications 164
- Purpose-Oriented Index 168
- Information 170
- IMPORTANT SAFETY INSTRUCTIONS 171
- SAVE THESE INSTRUCTIONS 171
Produits connexes et manuels pour Équipement musical supplémentaire Roland RD-700
(24 pages)
(80 pages)
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.375 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels