Roland RD-700 Manuel d'utilisateur Page 14
- Page / 172
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
14
Panel Descriptions
Rear Panel
1 GND Terminal
Connect using a grounded cable (optional) as conditions
require.
In some cases, depending on the environment in which the
unit is installed, the surface of the panel may sometimes feel
rough and grainy. This is due to an infinitesimal electrical
charge, which is absolutely harmless. However, if you are
concerned about this, connect the ground terminal with an
external ground. When the unit is grounded, a slight hum
may occur, depending on the particulars of your installation.
If you are unsure of the connection method, contact the
nearest Roland Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
Unsuitable places for connection
- Water pipes (may result in shock or electrocution)
- Gas pipes (may result in fire or explosion)
- Telephone-line ground or lightning rod (may be
dangerous in the event of lightning)
2 [POWER] Switch
Switch turns the power on/off (p. 24).
3 AC Inlet
Connect the included power cable to this inlet. (p. 22).
4 Wave Expansion Board Installation
Slot
Remove the cover for installation of optional wave expansion
boards (SRX Series) (p. 15).
5 MIDI Connectors (IN, OUT, THRU)
Used for connecting external MIDI devices and for
transmission of MIDI messages (p. 22, p. 59, p. 95).
6 PEDAL Jacks (DAMPER, FC1, FC2)
Connecting the pedal switch (DP-6) provided with the RD-
700 to the DAMPER jack allows you to use the switch as a
damper pedal.
With an optional expression pedal (such as the EV-5 or other
model) connected to the FC-1 or FC-2 jack, you can then
assign a variety of functions to the pedal (p. 23, p. 73).
7 OUTPUT R/L (MONO) Connectors
Provide output of the audio signals. These are connected to
an amp or other device. For monaural output use the L/
MONO jack (p. 22).
These also feature balanced output.
8 PHONES Jack
A set of headphones can be connected to this jack (p. 22).
Even when headphones are connected, sound will still be
output from the output jacks.
THRU OUT IN
MIDI
FC 1 FC 2DAMPER
PEDAL
R
L
(
MONO
)
OUTPUT
PHONES
BALANCED
TIP
RING
SLEEVE
HOT
COLD
GND
1
2
3
4
5 6 7
8
RD-700_e.book 14 ページ ２００４年４月２６日 月曜日 午前１１時５４分
- Owner’s Manual 1
- USING THE UNIT SAFELY 3
- IMPORTANT NOTES 5
- Main Features 6
- Contents 10
- General MIDI 11
- General MIDI 2 11
- Panel Descriptions 12
- 12 13 14 13
- Rear Panel 14
- Getting Ready 15
- Installing SRX Series Boards 16
- Equipment 22
- Connecting Pedals 23
- Turning the Power On and Off 24
- Adjusting the Volume 25
- (Factory Reset) 26
- After performing a Factory 27
- Reset, you may need to re 27
- When this occur, adjust 27
- (LCD Contrast) 28
- (Master Tune) 29
- Overview of the RD-700 31
- About the CURSOR Buttons 33
- Changing the Settings Values 33
- Performing with the Keyboard 35
- ([NUM LOCK]) 37
- Playing a Rhythm Set 38
- To Switch to Single Mode 41
- You can change the split 43
- Please refer to “Changing 43
- Point” (p. 44) 43
- Parts (PART SWITCH/LEVEL) 45
- ([TRANSPOSE]) 46
- BENDER BENDER 48
- You Play ([ARPEGGIO]) 49
- Changing the Arpeggio Style 50
- Changing Arpeggio Tempos 50
- Playing Rhythm ([RHYTHM]) 51
- Changing the Rhythm Pattern 52
- Changing Rhythm Tempos 52
- (MULTI EFFECTS) 53
- 12,4,8 3,6 359,10 56
- Settings Not Saved in a Setup 58
- Setup <000> 58
- What’s MIDI? 59
- MIDI Send Channel Settings 60
- (MIDI TX Part) 62
- Detailed Settings for 63
- Transmitted Parts ([MIDI TX]) 63
- Master Keyboard 64
- (Piano Edit) 66
- Settings (EQ-SW/EQ Gain/ 67
- EQ Frequency/EQ Q) 67
- Parameters That Can Be Set 68
- Edit Mode 69
- Setting the Keyboard Touch 71
- (Key Touch) 71
- Pedal, [CONTROL] Knob, and 73
- Equalizer Settings 73
- (Control/EQ) 73
- Tones (Tone Wheel Mode) 75
- Setting the Multi-Effects 76
- Reverb, and Chorus Effects 76
- (MFX/Reverb/Chorus) 76
- Making Multi-Effects Settings 77
- Making Reverb Settings 78
- Setting Chorus and Delay 78
- How to Make Settings 79
- Making the Rhythm Settings 82
- (Rhythm Pattern) 82
- Making Arpeggio Settings 83
- (Arpeggio) 83
- 90 10 90 10 86
- 50 50 50 50 86
- (Internal Part Prm) 89
- Setting MIDI Receive Parts 89
- Other Functions (Utility) 92
- Connecting MIDI Devices 95
- Recording the Performance 96
- About the Local Switch 96
- Sound Generator from an 97
- External MIDI Device 97
- Using the RD-700 as a GM 98
- Sound Module (GM Mode) 98
- Troubleshooting 100
- Error Messages/Other Messages 103
- Effect/Parameter List 104
- Effects Parameter List 126
- Appendices 127
- Reverb Parameters 134
- Chorus Parameters 134
- Tone List 135
- Rhythm Set List 138
- Arpeggio Style List 142
- Rhythm Pattern List 143
- Setup List 144
- Shortcut List 145
- MIDI Implementation 146
- 2. Data Transmission 151
- 3. Parameter Address Map 153
- 4. GS (Model ID = 42H) 157
- MIDI Implementation Chart 162
- Main Specifications 164
- Purpose-Oriented Index 168
- Information 170
- IMPORTANT SAFETY INSTRUCTIONS 171
- SAVE THESE INSTRUCTIONS 171
Produits connexes et manuels pour Équipement musical supplémentaire Roland RD-700
(24 pages)
(80 pages)
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.531 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels