Roland RD-700 Manuel d'utilisateur Page 96
- Page / 172
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
96
Connecting External MIDI Devices
Connecting MIDI Devices
Recording the Performance
Use the following procedure when recording to an external
sequencer.
1.
Turn on the external sequencer’s Thru function.
For details, refer to the following section “About Local
Switch.”
Refer to your sequencer owner’s manual for instructions
on how to carry out this procedure.
2.
Select the Setup for the performance to be recorded.
For instructions on selecting the Setup, refer to p. 54.
3.
Set the Rec Setting.
Use the procedure described in the previous section
“Settings for Recording” to make the following settings.
Rec Mode: ON
Local Switch: OFF
4.
Begin recording with the external sequencer.
5.
Bulk Dump the Setup.
Using the Utility Bulk Dump Temporary in Edit mode,
transmit the contents of the selected Setup to the external
sequencer.
For instructions on carrying out this operation, refer to
“Transferring the RD-700’s Settings to an External
MIDI Device (Bulk Dump)”
(p. 92).
6.
Perform on the RD-700.
7.
When the performance is finished, stop recording with
the external sequencer.
Recording is now complete.
You can then listen to the recorded performance by
playing it back on the external sequencer.
Exiting Rec Mode
When Rec Mode is set to ON, you cannot change the MIDI
TX settings. When you have finished recording the
performance, use the procedure described in the previous
section “Settings for Recording” to set Rec Mode to OFF.
NOTE
The settings made in Rec Setting cannot be saved. Rec Setting
automatically switch to “
Rec Mode: OFF, Local Switch:
ON
” when the power is turned on.
About the Local Switch
The switch that connects and disconnects the MIDI
connection between the keyboard controller section and the
sound generator section (p. 31) is called the Local switch.
Since essential information describing what is being played
on the keyboard won’t reach the sound generator if the Local
switch is set to OFF, the Local switch should normally be left
ON.
However, if while performing you want to send that
performance data to an external sequencer as MIDI messages
to be recorded, you then perform with the externally
connected MIDI sequencer set to MIDI Thru (whereby data
received from MIDI IN is then output from the MIDI OUT
with no changes made to the data).
In this case, the data sent over two paths, i.e., the data sent
directly from the keyboard controller section and the data
sent from the keyboard controller section via the external
sequencer, ends up being sent to the sound generator section
simultaneously. Thus, for example, even when you play a
“C” key only once, the note “C” cannot be sounded correctly,
as the sound is played by the sound generator section twice.
MIDI OUT MIDI IN
MIDI IN MIDI OUT
RD-700
Sequencer
Recording
MIDI Thru: On
Local Switch: Off
Keyboard Controller
Section
Sound
Generator
Section
RD-700_e.book 96 ページ ２００４年４月２６日 月曜日 午前１１時５４分
- Owner’s Manual 1
- USING THE UNIT SAFELY 3
- IMPORTANT NOTES 5
- Main Features 6
- Contents 10
- General MIDI 11
- General MIDI 2 11
- Panel Descriptions 12
- 12 13 14 13
- Rear Panel 14
- Getting Ready 15
- Installing SRX Series Boards 16
- Equipment 22
- Connecting Pedals 23
- Turning the Power On and Off 24
- Adjusting the Volume 25
- (Factory Reset) 26
- After performing a Factory 27
- Reset, you may need to re 27
- When this occur, adjust 27
- (LCD Contrast) 28
- (Master Tune) 29
- Overview of the RD-700 31
- About the CURSOR Buttons 33
- Changing the Settings Values 33
- Performing with the Keyboard 35
- ([NUM LOCK]) 37
- Playing a Rhythm Set 38
- To Switch to Single Mode 41
- You can change the split 43
- Please refer to “Changing 43
- Point” (p. 44) 43
- Parts (PART SWITCH/LEVEL) 45
- ([TRANSPOSE]) 46
- BENDER BENDER 48
- You Play ([ARPEGGIO]) 49
- Changing the Arpeggio Style 50
- Changing Arpeggio Tempos 50
- Playing Rhythm ([RHYTHM]) 51
- Changing the Rhythm Pattern 52
- Changing Rhythm Tempos 52
- (MULTI EFFECTS) 53
- 12,4,8 3,6 359,10 56
- Settings Not Saved in a Setup 58
- Setup <000> 58
- What’s MIDI? 59
- MIDI Send Channel Settings 60
- (MIDI TX Part) 62
- Detailed Settings for 63
- Transmitted Parts ([MIDI TX]) 63
- Master Keyboard 64
- (Piano Edit) 66
- Settings (EQ-SW/EQ Gain/ 67
- EQ Frequency/EQ Q) 67
- Parameters That Can Be Set 68
- Edit Mode 69
- Setting the Keyboard Touch 71
- (Key Touch) 71
- Pedal, [CONTROL] Knob, and 73
- Equalizer Settings 73
- (Control/EQ) 73
- Tones (Tone Wheel Mode) 75
- Setting the Multi-Effects 76
- Reverb, and Chorus Effects 76
- (MFX/Reverb/Chorus) 76
- Making Multi-Effects Settings 77
- Making Reverb Settings 78
- Setting Chorus and Delay 78
- How to Make Settings 79
- Making the Rhythm Settings 82
- (Rhythm Pattern) 82
- Making Arpeggio Settings 83
- (Arpeggio) 83
- 90 10 90 10 86
- 50 50 50 50 86
- (Internal Part Prm) 89
- Setting MIDI Receive Parts 89
- Other Functions (Utility) 92
- Connecting MIDI Devices 95
- Recording the Performance 96
- About the Local Switch 96
- Sound Generator from an 97
- External MIDI Device 97
- Using the RD-700 as a GM 98
- Sound Module (GM Mode) 98
- Troubleshooting 100
- Error Messages/Other Messages 103
- Effect/Parameter List 104
- Effects Parameter List 126
- Appendices 127
- Reverb Parameters 134
- Chorus Parameters 134
- Tone List 135
- Rhythm Set List 138
- Arpeggio Style List 142
- Rhythm Pattern List 143
- Setup List 144
- Shortcut List 145
- MIDI Implementation 146
- 2. Data Transmission 151
- 3. Parameter Address Map 153
- 4. GS (Model ID = 42H) 157
- MIDI Implementation Chart 162
- Main Specifications 164
- Purpose-Oriented Index 168
- Information 170
- IMPORTANT SAFETY INSTRUCTIONS 171
- SAVE THESE INSTRUCTIONS 171
Produits connexes et manuels pour Équipement musical supplémentaire Roland RD-700
(24 pages)
(80 pages)
(8 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.294 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels