Roland TD-8 Manuel d'utilisateur télécharger pdf (Page 203)

201

MIDI-Implementation

Anhang

❍General purpose controller 1 (Controller number 16)

Status 2nd byte 3rd byte

BnH 10H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Control value: 00H - 7FH (0 - 127)

* Only the channel assigned to the drum kit part can be received.

* If the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC or ZONE CC are set to "GEN1",

the effect will apply to the specified parameter.

* During recording, this will be recorded in the sequencer data as PEDAL CC data or

ZONE CC data.

❍General purpose controller 2 (Controller number 17)

Status 2nd byte 3rd byte

BnH 11H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Control value: 00H - 7FH (0 - 127)

* Only the channel assigned to the drum kit part can be received.

* If the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC or ZONE CC are set to "GEN2",

the effect will apply to the specified parameter.

* During recording, this will be recorded in the sequencer data as PEDAL CC data or

ZONE CC data.

❍Hold 1 (Controller number 64)

Status 2nd byte 3rd byte

nH 40H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON

* Only the channel assigned to the backing part can be received.

* When recording, this is recorded in the sequencer data itself.

❍Effect 1(Reverb Send Level) (Controller number 91)

Status 2nd byte 3rd byte

BnH 5BH vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Reverb send level: 00H - 7FH (0 - 127)

* Only the channel assigned to the backing part can be received.

* When recording, this is recorded in the sequencer data itself.

❍RPN MSB/LSB (Controller number 101, 100)

Status 2nd byte 3rd byte

BnH 65H mmH

BnH 64H llH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

mm = upper byte of parameter number specified by RPN (MSB)

ll = lower byte of parameter number specified by RPN (LSB)

* Only the channel assigned to the backing part can be received.

* The value specified by RPN will not be reset even by messages such as program change

or reset all controllers.

* When recording, this is recorded in the sequencer data itself.

**RPN**

The RPN (Registered Parameter Number) messages are expanded control changes,and each

function of an RPN is described by the MIDI Standard.

To use these messages, you must first use RPN (controller number 100 and 110, their order

does not matter) to specify the parameter to be controlled, and then use Data Entry

messages (controller number 6, 38) to specify the value of the specified parameter. Once an

RPN parameter has been specified, all data entry messages received on that channel will

modify the value of that parameter. To prevent accidents, it is recommended that you set

RPN null (RPN number = 7FH 7FH) when you have finished setting the value of the desired

parameter. Refer to “■Examples of actual MIDI message” <Example 4> (p. 212).

On the normal mode of TD-8, RPN can be used to modify the following parameters.

Regarding the value of each parameter, refer to Data Entry (Controller number 6).

RPN

MSB LSB

Parameter

00H 00H Pitch Bend Sensitivity

7FH 7FH RPN null

● Program Change

Status 2nd byte

CnH ppH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

pp = Program number: 00H - 7FH (prog.1 - prog.128)

* Not Received when [SETUP]-[MIDI]-[PROG] PROGRAM CHANGE RX SW is set to

“OFF”.(Initial Value is ON)

* The sound will change beginning with the next note-on after the program change is

received. Voices which were already sounding before the program change was received

will not be affected.

* Not recorded in the sequencer.

● Pitch Bend Change

Status 2nd byte 3rd byte

EnH llH mmH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

mm, ll = Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

* Only the channel assigned to the backing part can be received.

* When recording, this is recorded in the sequencer data itself.

■ Channel Mode Messages

● All Sounds Off (Controller number 120)

Status 2nd byte 3rd byte

BnH 78H 00H

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

* When this message is received, all currently-sounding notes on the corresponding

channel will be silenced. However, the status of channel messages will not change.

* When recording, this is recorded in the sequencer data itself.

● Reset All Controllers (Controller number 121)

Status 2nd byte 3rd byte

BnH 79H 00H

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

* When this message is received, the following controllers will be set to their reset values.

* When recording, a control message carrying the reset value will be created and recorded.

Controller Reset value

Pitch Bend Change +/-0 (center)

Polyphonic Key Pressure 0 (off)

Modulation 0 (off) (When set to PEDAL CC or ZONE CC.)

Foot Control 0 (off) (When set to PEDAL CC.)

General Purpose Controller1 0 (off) (When set to PEDAL CC or ZONE CC.)

General Purpose Controller2 0 (off) (When set to PEDAL CC or ZONE CC.)

Hold1 0 (off)

RPN unset; previously set data will not change

● All Notes Off (Controller number 123)

Status 2nd byte 3rd byte

BnH 7BH 00H

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

* When All Notes Off is received, all notes on the corresponding channel will be turned

off. However if Hold 1 is ON, the sound will be continued until these are turned off.

* In the recording mode, “Note OFF message” will be created for corresponding Note ON

message, and will be recorded.

1 2 ... 198 199 200 201 202 203 204 205 206 207 208 ... 223 224

Roland TD-8 Manuel d'utilisateur Page 203

Commentaires sur ces manuels

Roland TD-8 Manuel d'utilisateur Page 203

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Roland TD-8