Roland TD-8 Manuel d'utilisateur télécharger pdf (Page 202)

200

MIDI-Implementation

TD-8 Drum-Soundmodul

Version 1.00

Normal mode

Section 1. Receive data

■ Channel Voice Messages

* Following Channel Voice Messages can be recorded in [SETUP]-[MIDI] TX/RX

CHANNEL.

● Note Off

Status 2nd byte 3rd byte

8nH kkH vvH

9nH kkH 00H

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

kk = note number: 00H - 7FH (0 - 127)

vv = note off velocity: 00H - 7FH (0 - 127)

* Only the channel assigned to the backing part can be received.

* The Velocity Values of Note Off message are ignored.

* When recording, this is recorded in the sequencer data itself.

● Note On

Status 2nd byte 3rd byte

9nH kkH vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

kk = note number: 00H - 7FH (0 - 127)

vv = note on velocity: 00H - 7FH (0 - 127)

* A channel which is assigned to the drum kit part will receive only the note numbers

which are specified by the drum kit.

* A channel which is assigned to the percussion part will receive only the note numbers

which are specified by the percussion set.

* When recording, this is recorded in the sequencer data itself.

● Polyphonic Key Pressure

Status 2nd byte 3rd byte

AnH kkH vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

kk = note number: 00H - 7FH (0 - 127)

vv = Value: 00H - 7FH (0 - 127)

* A channel which is assigned to the drum kit part will receive only the note numbers

which are specified by the drum kit.

* If the value is greater than 40H (64), the decay of the note sounded by the received note

number will be shortened.

* Not recorded in the sequencer.

● Control Change

❍Bank Select (Controller number 0, 32)

Status 2nd byte 3rd byte

BnH 00H mmH

BnH 20H llH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

mm = Bank number MSB: 00H - 7FHÅibank.1 - bank.128Åj

ll = Bank number LSB: processed as 00H

* Not Received when [SETUP]-[MIDI]-[PROG] PROGRAM CHANGE RX SW is set to

“OFF”.(Initial Value is ON)

* Bank select processing will be suspended until a program change message is received.

* Only the channel assigned to the backing part can be received.

* Not recorded in the sequencer.

❍Modulation (Controller number 1)

Status 2nd byte 3rd byte

BnH 01H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Modulation depth: 00H - 7FH (0 - 127)

* Only the channel assigned to the drum kit part can be received.

* If the [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC or ZONE CC are set to "MOD",

the effect will apply to the specified parameter.

* During recording, this will be recorded in the sequencer data as PEDAL CC data or

ZONE CC data.

❍Foot Control (Controller number 4)

Status 2nd byte 3rd byte

BnH 04H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Control value: 00H - 7FH (0 - 127)

* Only the channel assigned to the drum kit part can be received.

* The effect will be obtained when [SETUP]-[MIDI]-[GLOBAL]-[PAGE 2] PEDAL CC is set

to "FOOT".

* When recording, this will be recorded as PEDAL CC data in the sequencer data itself.

❍Data Entry (Controller number 6)

Status 2nd byte 3rd byte

BnH 06H mmH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

mm = The value of the parameter specified by RPN.

* Only the channel assigned to the backing part can be received.

* Not recorded in the sequencer.

On the normal mode of TD-8, RPN can be used to modify the following parameters.

RPN Data entry

MSB LSB MSB LSB Explanation

00H 00H mmH --- Pitch Bend Sensitivity

mm: 00H - 18H (0 - 24 semitones)

LSB: ignored (processed as 00H)

specify up to 2 octaves in semitone steps

7FH 7FH --- --- RPN null

set condition where RPN is unspecified. The data

entry messages after set RPN null will be

ignored.(No Data entry messages are required

after RPN null).

Settings already made will not change.

MSB, LSB of data entry: ignored

❍Volume (Controller number 7)

Status 2nd byte 3rd byte

BnH 07H vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = Volume: 00H - 7FH (0 - 127)

* Volume messages are used to adjust the volume barance of each part.

* Only the channel assigned to the percussion part and the backing part can be received.

* Not recorded in the sequencer.

❍Pan (Controller number 10)

Status 2nd byte 3rd byte

BnH 0AH vvH

n = MIDI channel number: 0H - FH (ch.1 - ch.16)

vv = pan: 00H - 40H - 7FH (Left - Center - Right)

* Only the channel assigned to the backing part can be received.

* Not recorded in the sequencer.

1 2 ... 197 198 199 200 201 202 203 204 205 206 207 ... 223 224

Roland TD-8 Manuel d'utilisateur Page 202

Commentaires sur ces manuels

Roland TD-8 Manuel d'utilisateur Page 202

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Roland TD-8