Roland SJ-740 Manuel d'utilisateur Page 108
- Page / 128
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
106
Chapter 6 What to Do If
6-1 The Machine Doesn't Run
The Printer Unit Doesn't Run
Is the power switched on?
Switch on the printer's main power, then press the sub power
switch and make sure the sub power switch lights up.
Is illuminated?
Printing is not performed when is not illuminated.
Pull back the loading lever, close the front cover, and press
.
Is the front cover open?
Close the front cover.
Is the top menu displayed?
If the top menu isn't displayed, printing doesn't start even
when data is sent from the computer. To go to the top menu,
press
, then press .
☞ P. 36, "Getting Ready to Receive Data from a Computer"
Is illuminated?
When lights up, operation is paused. To resume,
press
. goes dark and printing resumes.
Has ink run out?
When printing data is sent while
the screen shown in the figure
is displayed, a message appears
and a warning beep sounds. At the same time, operation
pauses. When the ink cartridge is replaced with a new one,
printing starts.
☞ P. 39 "If Ink Runs Out"
☞ P. 77, "Determining What Happens When an Ink Cartridge Is Empty"
Is a message displayed on the screen?
☞ P. 113, "If a Message Appears"
☞ P. 114, "If an Error Message Appears"
Is the power cord connected?
Connect the power cord securely.
Is the Link LED lighted?
If the Link LED for the Ethernet connector is not lighted, it
means that a correct connection to the network has not
been made. Make sure the network routing is suitable. Try
connecting the computer and the machine to the same hub,
or connecting them directly using a crossover cable. If this
makes it possible to perform printing, it means the problem
is in the network itself.
Are the network settings correct?
If printing is not possible even though the Link LED is lighted,
check to make sure the IP address and other such settings
are correct. The settings on both the machine and the com-
puter must be appropriate. Redo the settings, checking to
ensure that the IP address doesn’t conflict with the IP ad-
dress for another device on the network, that the port set-
ting for the software RIP specifies the IP address set on the
machine, that the settings have no typing errors, and for
other such problems.
☞ Setup Guide
☞ P. 92, "Setting the IP Address, Subnet Mask, Etc."
Did the software RIP end abnormally?
Make sure the software RIP is running correctly, then switch
the sub power switch off and back on.
The Media Take-up System Doesn't Run
Is the take-up unit cable connected?
Connect the take-up unit cable to the machine. To perform
take-up automatically during printing, also make the set-
ting for the AUTO switch.
☞ Setup Guide
☞ P. 45, "Loading Roll Media"
The Media Heating System Doesn't Warm Up
Is media loaded?
The media heating system does not warm up to the preset
temperature when
is dark (by default). Load media,
press
, and wait for the machine to warm up.
☞ P. 87, "Determining How the Media Heating System Operates"
Is the temperature of the room too low?
Use the machine in an environment where the temperature
is 20 to 32˚C (68 to 90˚F).
1 2 3 4 5 6
7 8 9 10 11 12
Link LED
- USER'S MANUAL 1
- For the USA 2
- For Canada 2
- Contents 3
- To Ensure Safe Use 6
- Warning Labels 12
- Avis sur les avertissements 13
- ATTENTION 13
- PRUDENCE 13
- À propos des symboles 13
- Printer unit 20
- Ink cartridges 20
- Chapter 1 21
- Introduction 21
- 1-1 Features of the Machine 22
- 1-2 Part Names and Functions 23
- Chapter 1 Introduction 24
- Operation Panel 25
- Media Take-up System 26
- Chapter 2 27
- Operation 27
- Sub power switch 28
- The Power-saving Feature 29
- Usable Media 30
- Loading Media 30
- Chapter 2 Operation 31
- OK Not OK 33
- Attach the media clamps 34
- Close the front cover 34
- How to Cut Off Media 35
- Procedure 36
- General Guide for Adjustment 37
- 2-4 Starting Printing 38
- Printing Tests and Cleaning 39
- 2-5 If Ink Runs Out 41
- Chapter 3 45
- Operation of the Media 45
- Take-up System 45
- 3-1 The Take-up System 46
- 3-2 Using the Take-up System 47
- Removing Taken-up Media 50
- Chapter 4 51
- Maintenance and Adjustment 51
- Disposing of Discharged Ink 52
- Cleaning 54
- Daily Care and Maintenance 55
- Periodic Care and Maintenance 55
- Start cleaning 56
- How to Perform Cleaning 58
- Maintenance cover 59
- Replacing the Wipers 62
- Replace the separating knife 64
- MAINTENANCE 65
- REPLACE KNIFE 65
- W 1839mm 65
- SETUP SHEET 65
- ROLL 65
- Keep Performing Maintenance 66
- Alarm Feature 66
- 4-6 When Moving the Unit 67
- Chapter 5 69
- Feature Reference 69
- Description 70
- Using Transparent Media 73
- Printing Hard-to-dry Media 75
- Using Sticky Media 77
- How to Load Sheet Media 78
- Changing the Type of Ink 79
- Deactivating the Sleep Mode 80
- Print a test pattern 84
- Chapter 5 Feature Reference 86
- Menu item Page to see 92
- Loading a Saved Preset 93
- Assigning a Name to a Preset 93
- Printing a System Report 96
- Viewing the Network Settings 97
- 5-11 Performing Maintenance 98
- 5-12 Menu List 100
- 12 Menu List 101
- Chapter 5 Feature Reference 101
- Language and Unit Menu 105
- Cleaning Menu 105
- Heater Configuration Menu 105
- Chapter 6 107
- What to Do If 107
- Chapter 6 What to Do If 108
- Colors Are Unstable or Uneven 109
- 6-3 The Media Jams 111
- Media Wrinkles or Shrinks 113
- Media Feed Is Not Straight 113
- Media Feed Is Not Smooth 113
- What to Do First 114
- 6-7 If a Message Appears 115
- Chapter 7 119
- Specifications 119
- 7-1 Usable Media 120
- 7-2 Printing Area 121
- Chapter 7 Specifications 122
- 7-4 Specifications 124
- R1-070820 128
Produits connexes et manuels pour Imprimer et scanner Roland SJ-740
(31 pages)
(99 pages)
(97 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.594 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels