Roland FR-1xb Manuel du propriétaire télécharger pdf (Page 22)

Editing FUNCTION settings

FR-1 V-Accordion

Parameters

In the following, the messages at the right edge of the

gray bars have the following meaning:

“OK”: Can be saved in the Global area (common to all Sets).

“POW”: Reset when you switch off the FR-1.

Note: The small dot “•” means “factory setting”.

This parameter allows you to change the FR-1’s overall tuning.

The factory default, “440”, represents the reference pitch used by

all electronic musical instruments. The settings you can select

with the registers are:

This parameter allows you to choose the system used for detun-

ing the 8’ reeds of the selected register. The settings you can

select with the registers are:

This parameter allows you to transpose all sections of the FR-1, so

as to play in one key and sound in another. The settings you can

select with the registers are:

This parameter is used to set the balance between the Treble and

Bass sections. When you press register [1], the Treble section is

inaudible, while pressing register [4] means that the Bass and

Chord section is no longer audible. The settings you can select

with the registers are:

These parameters allow you to set the level of the ORCHESTRA,

BASS or CHORD orchestral sound, or of the DRUMS function for a

better balance with the other available sections. The settings you

can select with the registers are (for all parameters):

The value “0” means that the factory-set balance setting is used.

This parameter allows you to set the metronome tempo. The set-

tings you can select with the registers are:

This parameter allows you to set the metronome’s time signature.

The settings you can select are:

This parameter allows you to change the metronome’s level when

it is too loud or too soft. See page 17 for details.

This parameter allows you to set the volume of the reverb effect

with respect to the accordion and/or orchestral sounds. It applies

to all sections that are currently switched on. The settings you

can select with the registers are:

This parameter allows you to specify what kind of effect the

Reverb processor should generate. The available options are:

Master Tune [B1]/[1]

415~440~466 (Hz)

Default setting: 440

1 415 3 448

2• 440 4 466

Musette Detune [C2]/[2]

Dry, Classic, F-Folk, American L,

American H, Nord Eur, German L,

D-Folk L, Italian L, German H,

Alpine, Italian H, D-Folk H, French,

Scottish

Default setting: Classic

Musette Detune

1• Classic 3 Italian L

2 Nord Eur 4 French

Transpose [C

2]/[3]

POW

–6~0~5

Default setting: 0

Transpose

1 –5 (G) 3 +2 (D)

2• 0 (C2) 4 +4 (E)

Treble/Bass & Chord Balance [D2]/[4]

POW

b1~63,0, t1~63

Default setting: 0

1 Bass & Chord 60 3 Treble 30

2• Equal balance 4 Treble 60

Orchestra/Organ Level

Drums Sound Level

Orchestra Bass Level

Orchestra Chord Level

2]/[5]

[E2]/[6]

[F2]/[7]

2]/[8]

–40~Std~40

Default setting: Std

1 –40 3 +20

2• 0 4 +40

Metronome Tempo [G2]/[9]

20~250

Default setting: 120

1 Adagio (72 BPM) 3 Allegro (144 BPM)

2• Moderato (120 BPM) 4 Presto (192 BPM)

Metronome Time Signature [G

2]/[10]

1/4, 2/4, 3/4, 4/4, 5/4, 6/4, 6/8, 9/8

Default setting: 4/4

12/43•4/4

23/446/8

Metronome Level [A2]/[11]

Off, Low, Medium, High

Default setting: Medium

1 Off 3• Medium

2 Low 4 High

Reverb Level [B

2]/[12]

0~127

Default setting: 48

10 (no reverb) 3 96

2• 48 4 127

Reverb Type [B2]/[13]

Room 1~3, Hall 1~2, Plate, Delay,

Panning Dly

Default setting: Plate

Room1 [1]

Room2

Room3

These effects simulate the reverberation of a

room. They provide a well-defined spacious

reverberation.

Hall1 [2]

Hall2

These types simulate the reverberation of a

concert hall with a deeper reverberation than

the Room reverbs.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 39 40

Commentaires sur ces manuels

Pas de commentaire

Roland FR-1xb Manuel du propriétaire Page 22

Commentaires sur ces manuels

Produits connexes et manuels pour Instruments de musique Roland FR-1xb