Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (p. 3–p. 5). These sections provide import
10 Front and rear panel fig.front 4. Input/output level indicators These LEDs light according to the level of the signals that are being input via th
11 Front and rear panel9. Sample rate select switch This specifies the sampling frequency at which audio data will be recorded and played back. In or
12 Front and rear panel fig.rear 17. Power switch Used to switch the power on (DC IN) or off (OFF), and for switching to bus power (BUS). fig.power-s
13 Front and rear panel20. Grounding terminal Depending on the circumstances of a particular setup, you may experience a discomforting sensation, or
14 Installing the driver (Macintosh) 1 With the FA-101 disconnected, start up your Macintosh. 2 Use a FireWire (IEEE 1394) cable to connect the FA-10
15 Installing the driver (Macintosh) * Depending on the model of Macintosh you are using, starting up the Macintosh when the FA-101 is connected may
16 Installing the driver (Macintosh) Now, let’s play back the sample data to verify that the connections and settings are correct. We will use iTunes
17 Installing the driver (Windows) What is a driver? A driver is software that allows data to be transferred between the FA-101 and application softw
18 Installing the driver (Windows) 8 From the Windows start menu, choose “Run...” The “Run” dialog box will appear. 9 Input the name into the d
19 Installing the driver (Windows) 14 A dialog box entitled “Completing the Found New Hardware Wizard” appears. Click [Finish] .Once again, the “
2IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.BLUE: BROWN: As the colours of the wires in the mains lea
20 Installing the driver (Windows) Next, you need to set your computer so priority is given to background services, which will help to assure that au
21 Installing the driver (Windows) Crackling may occur in the sound if you omit making this setting. To ensure that audio and MIDI are processed smoo
22 Installing the driver (Windows) In order to get the best performance from the software you are using, you must choose the correct device settings.
23 Installing the driver (Windows) If you will be using the Windows Media Player application with the FA-101, specify the input/output devices as fol
24 Installing the driver (Windows) Now, let’s play back the sample data to verify that the connections and settings are correct. We will use standard
25 Basic connections and settings This section explains basic connections and data flow for the FA-101.Refer to the block diagram printed on the fron
26 Basic connections and settings Here’s how to make connections and settings to let you sing or play your guitar while listening to audio data on yo
27 Basic connections and settings Input sensitivity knob Use the input sensitivity knob to adjust the input level. For the best audio quality, raise
28 Basic connections and settings fig.digital Connections Connect your digital device to the digital input connector. Sample rate select switch Set t
29 Basic connections and settings fig.send-return Connections Connect output jacks 3–8 to your external mixer or other device.Connect the outputs of
3 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. ...
30 Software settings You will need to make audio and MIDI device settings for the software you’re using. Here are some examples for typical software
31 Software settings fig.sonar-2.eps 8. Click the Drivers tab.In the lists of Input Drivers and Output Drivers , click the following devices to
32 Software settings In this example we are using Digital Performer 4.12. fig.digiperf.eps 1. Power up the FA-101, and then start up Digital Performe
33 Software settings In this example we are using the Macintosh version of Cubase SX/SL. 1. Power up the FA-101, and then start up Cubase. 2. From th
34 Software settings Here is an example using Logic Platinum 6. 1. Power up the FA-101, and then start up Logic. 2. From the Logic Platinum menu, c
35 Software settings There is no FA-101 Driver Settings dialog box on Macintosh. Make settings from within your software.You can adjust the audio lat
36 Software settings If you still experience clicks or pops even though you have specified the largest buffer size, check Use Maximum Buffer Setting
37 Troubleshooting If you experience problems, read this chapter first/ It contains tips for solving most problems. You attempted to install as descr
38 Troubleshooting Does your computer or FireWire (IEEE 1394) repeater hub have a sufficient power supply? If you are using bus power, the FA-101 can
39 Troubleshooting Are the volume controls of the FA-101 set appropriately? Adjust the headphone volume knob and direct monitor volume of the FA-101’
4 012b • Immediately turn the power off, remove the AC adaptor from the outlet, and request servicing by your retailer, the nearest Roland Service Ce
40 Troubleshooting Are the input sensitivity knobs and direct monitor volume knob set appropriately? Turn the knobs toward the right to adjust the vo
41 Troubleshooting In Windows, did you make the setting described in “Giving priority to background services”? In order to ensure that audio/MIDI pro
42 Troubleshooting Could two or more computers be connected to the FA-101 or to your mixer or audio devices? Try connecting the FA-101 to only one co
43 Troubleshooting Is the FA-101 connected to a FireWire (IEEE 1394) hub? Try connecting the FA-101 directly to the FireWire (IEEE 1394) connector of
44 Troubleshooting Has a mic or guitar been left connected? If a mic or guitar is connected to the FA-101, disconnect the mic or guitar and turn the
45 Troubleshooting The first time you use the FA-101 with Cubase, turn on the power with the FA-101's sample rate select switch at the 44.1 kHz
46 Main Specifications ● Number of Audio Record/Playback Channels <44.1/48/88.2/96 kHz> (Full duplex)Record: 10 channelsPlayback: 10 channels
47 Index Numerics 4-pin ... 12 6-pin ...
As of December 10, 2005 (EDIROL-1)Information When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL
5 IMPORTANT NOTES 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 3, please read and observe the following: Power Supply 3
6 Handling CD-ROMs 801 • Avoid touching or scratching the shiny underside (encoded surface) of the disc. Damaged or dirty CD-ROM discs may not be rea
7 Contents Contents of the package ... 8Front and rear panel ...
8 Contents of the package FA-101 fig.FA-101 AC adaptor This is the dedicated AC adaptor for the FA-101. Use only the supplied AC adaptor. FireW
9 Front and rear panel fig.frontfig.jack-type 1. Combo input jacks These are analog audio input jacks with mic preamps. They accommodate either XLR o
Commentaires sur ces manuels